Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Americans arn`t a race eighter CULTURE is...

    Americans arn`t a race eighter

    CULTURE is what keeps them overweight

    CULTURE is what keeps them thinking they have leagal and moral rights to all world resources

    CULTURE is what makes them...
  2. Replies
    46
    Views
    2,893

    Go from there Then find which auxilary...

    Go from there

    Then find which auxilary contacts to use for forward-reverse So you can connect these to the switch controlled by the handle on the apron
    Then perhaps a emergency button
    Then...
  3. Replies
    14
    Views
    1,709

    The bigger the drive the less the absolute...

    The bigger the drive the less the absolute differences in lenght matter
    Peter
  4. Obvious First weld on the fittings then cut the...

    Obvious
    First weld on the fittings then cut the thread :D

    Peter
  5. Although the taper has a short lenght I would set...

    Although the taper has a short lenght I would set the tool death center
    Also if you use a indicator on a taper
    The bore will be convex otherwise

    Peter
  6. Replies
    14
    Views
    1,709

    See post 2 Then did you check the grooves of...

    See post 2
    Then did you check the grooves of the poelies were the same???

    Peter
  7. You could softsolder on a piece of 2mm square...

    You could softsolder on a piece of 2mm square brass on the last 2mm That would not matter that much But i would give it a try as it is and see how it goes

    Peter
  8. Replies
    40
    Views
    2,236

    If you stop the spindle it should come to a quick...

    If you stop the spindle it should come to a quick stop Ecspecialy the last bit If not the bearings are too loose Also make sure you use the right oil for the spindle Thin as water
    Peter
  9. Do not glue the shim in place Thickness of the...

    Do not glue the shim in place
    Thickness of the glue layer will not be constant
    It only matters when installing It is static furthermore as it is at the back of the gib
    I sometimes bend over one...
  10. The tube perhaps is missing a piece that is meant...

    The tube perhaps is missing a piece that is meant to set the position of the cutting edge of the drill
    A drill chuck with a morse taper can hold the smaller drills

    Peter
  11. Shrink fit a collar around the extension rod...

    Shrink fit a collar around the extension rod instead of glueing the drill in it
    A hydraulic or mecanical shrink collar is also not so difficult to make
    Another idea is to make a taper on the OD...
  12. The 1:2 ratio is to drive a cam for clearance...

    The 1:2 ratio is to drive a cam for clearance for a 2 lip drill Perhaps it is possible to change the ratio to 1:3 or 1:4
    Does it come with a cam ??

    Peter
  13. Probably for drill sharpening Peter

    Probably for drill sharpening

    Peter
  14. Replies
    13
    Views
    1,407

    Hit the brass plug with a hammer on the head a...

    Hit the brass plug with a hammer on the head a couple of times
    If it is not glued in it comes loose to unscrew pretty fast
    Hitting it with a hammer is always my first thing to do with stuck...
  15. Replies
    31
    Views
    2,266

    Do not use bolts but studs with a nut if possible...

    Do not use bolts but studs with a nut if possible
    You insert the stud only once So less wear

    Peter
  16. Replies
    10
    Views
    549

    I woud not call them machines as it has no motor...

    I woud not call them machines as it has no motor but I would call them devices
    It is just a rod with a slit in it positioned in 2 V blocks with one a bit adjustable
    The rod has a square for a...
  17. Replies
    10
    Views
    549

    Here is a video https://youtu.be/eFdm7R8l1a4...

    Here is a video

    https://youtu.be/eFdm7R8l1a4
    This is used to make gutters from zinc The result is a bit different as drawn
    The bar with the slit in iot is drivenmanually by a long crank
    I...
  18. Many Italian cars are concidered crappy in Europe...

    Many Italian cars are concidered crappy in Europe too :D
  19. Most american machinery(and cars) was considered...

    Most american machinery(and cars) was considered crappy over here
    Partly because of being imperial mostly Partly because of the crap imported by the Marshall plan "help" we got

    Peter
  20. Thermite is mostly a treat for newcommers Those...

    Thermite is mostly a treat for newcommers
    Those who know him Well they know
    So keep laughing and just inform newcommers that he is the joker of the forum if you feel the need
    A bit more politly...
  21. Replies
    9
    Views
    748

    Is there a devider in the line ?? Peter

    Is there a devider in the line ??

    Peter
  22. Replies
    13
    Views
    1,063

    Some mustard after the meal You could have...

    Some mustard after the meal
    You could have rotated the shield 90-180 or 270 dgr and see if it runs free then


    Peter
  23. And the earth is flat Never ever landed on the...

    And the earth is flat
    Never ever landed on the moon eighter
    :stirthepot:

    Peter
  24. Over here Repairshops have CNC machines Along...

    Over here Repairshops have CNC machines Along with some manual machines yes But their main machines are CNC (and I sell manual machines for a living you know)
    And over here (and in the US probbably...
  25. Yes "Made " Not anymore ?? But that is why I...

    Yes "Made "
    Not anymore ??
    But that is why I said "In general" Always some exceptions

    Peter
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4