Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: TD-4242

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. Did you ever find one?

    Did you ever find one?
  2. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    yep, I'll ask if it's ok to forward them if...

    yep, I'll ask if it's ok to forward them if anyone else needs them after I test them out later tonight.

    Edit: was a bit of a process, but set the parameters that were given and they worked.
    ...
  3. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    Good and bad from contact with Yaskawa, they no...

    Good and bad from contact with Yaskawa, they no longer support the MX1, If they happen to have parts they can do certain services though and they did give me the required parameters.
  4. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    Thank you, I'll get in contact with them right...

    Thank you, I'll get in contact with them right away.
  5. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    I did find D&Ls number and will be giving Larry a...

    I did find D&Ls number and will be giving Larry a call. MCKenna posted "Effective January 1, 2020 McKenna Service Company will no longer provide technical support for the ACROLOC equipment. If...
  6. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    Is there a place I can purchase this parameter...

    Is there a place I can purchase this parameter for a device 30 years out of support?
  7. Thread: Yasnac MX1 WCS

    by TD-4242
    Replies
    10
    Views
    804

    Yasnac MX1 WCS

    Anyone know the hidden parameter to turn on the g52,g54-9 wcs option?

    Right now trying to use them I get "UNUSABLE G CODE OR G CODE NOT INCLUDED IN OPTIONS PROGRAMMED" when trying to use it.
  8. Replies
    10
    Views
    2,313

    I found this here, what'cha got?

    I found this here, what'cha got?
  9. Replies
    3
    Views
    1,933

    double that on the DL-325L, I also need to...

    double that on the DL-325L, I also need to replace the button/blister film on mine. Don't know what options are available to get a one-off printed for resonable moneys.
  10. Replies
    5
    Views
    480

    Mine's the 10 series and it's just a...

    Mine's the 10 series and it's just a learning/hobby machine. Much cheaper than a tormach although a lot harder to move. I do seem to have drip feeding working pretty well. As you say slow it down....
  11. Replies
    4
    Views
    928

    several microns!!!

    several microns!!!
  12. Replies
    5
    Views
    480

    I guess people don't like the proprietary tool...

    I guess people don't like the proprietary tool holder and relatively light weight spindle compared to the rest of the machine. I'm happy 'cause I got a hobby machine that's 10x the size/capability...
  13. Replies
    5
    Views
    480

    Drip Feeding to Yasnac MX1

    I've recently picked up an old CNC machine for my garage shop. It was old, cheap and really well cared for so even though it's the infamous Acroloc so far it seems better than the reputation. After...
  14. Yasnac MX1 PDF Documents OCR'ed so they are searchable

    Operators Manual
    https://github.com/TD-4242/Yasnac-MX1-Documentation/raw/master/Yasnac%20MX1%20Operators%20Manual%20TOE-C843-7-30.pdf

    Maintenance Manual...
  15. Replies
    191
    Views
    401,540

    Sticky: In my case my self starter occasionally stalls on...

    In my case my self starter occasionally stalls on start so if power loss happens and I'm not right by it, it could burn up the motor.
  16. Replies
    13
    Views
    1,172

    For now, since I'm just learning G-code and the...

    For now, since I'm just learning G-code and the machine and not doing multiple parts, I'm sticking with G92 as the offset. Hopefully I can find a solution to the G54-59 issue by the time I needed it.
  17. Replies
    13
    Views
    1,172

    yea, same issue. Any line with G54 sets the WCS...

    yea, same issue. Any line with G54 sets the WCS but then throws an alarm that has to be reset to continue.
  18. Replies
    13
    Views
    1,172

    Very interesting and disappointing. Living in...

    Very interesting and disappointing. Living in the current shared tech and open source world has warped my mind and made me forget how secretive everything was back then. I'd hope that since they...
  19. Hope you're not still waiting on an answer, but I...

    Hope you're not still waiting on an answer, but I just took apart my tool changer and found the center retaining collar that holds the disc has 4 allen head screws in it that you can loosen and then...
  20. Replies
    13
    Views
    1,172

    So why does G54 work offset work then? I can set...

    So why does G54 work offset work then? I can set G54 either with G10 call or manually in the parameters screen #6517-6519 to be 3 inches off machine zero in X/Y, call G54 and get the error, reset...
  21. Replies
    13
    Views
    1,172

    Just testing with a very simple hand written...

    Just testing with a very simple hand written gcode, not actually making a part:

    O0099
    N10 G10 Q2 P1 X3. Y-3. Z-1.;
    N20 G90;
    N30 G00 G54 X0. Y0. Z0.;
    M30;

    N10 is used to set the G54 offset,...
  22. Replies
    13
    Views
    1,172

    Old Yasnac controller G54 issue

    Likely just something I don't know as I bought this machine and brought it into my little hobby shop to learn some CNC stuff.

    I've been able to zero the machine, then setup a G54 offset and make...
  23. Thanks for the attention to the sticky I seemed...

    Thanks for the attention to the sticky I seemed to have missed. I will keep an eye on it closely.
  24. I figured I could do that, I guess my questions...

    I figured I could do that, I guess my questions are:
    1) The historical use of this motor was a shop with normal 3 phase service (either 208,240,480 not sure)
    2) what effect might this have on the...
  25. Hooking up a VFD to 3 phase motor, plate says 200v?

    I'm hooking up a VFD to power a Clausing 1500 lathe with a Doerr 7.5hp motor. I know this machine was powered by standard commercial 3 phase line when I tested it, although I don't know for sure if...
Results 1 to 25 of 30
Page 1 of 2 1 2