Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ChipSplitter

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. You sure that's not just a bunch of malarkey..???...

    You sure that's not just a bunch of malarkey..???

    :D
  2. Someone is gonna pay income tax on that in a year...

    Someone is gonna pay income tax on that in a year from now. (No such thing as a free lunch.........)

    If you don't believe that, you're whistling in the graveyard. :sulk:
  3. Replies
    16
    Views
    402

    Disclaimer: I haven't done AR500, just AR400. ...

    Disclaimer: I haven't done AR500, just AR400.

    Yes it can be done, drill your hole as large as the customer will allow, buy a good tap (OSG, Emuge, Guhring, Nachi), use a good tap lube (Moly-Dee...
  4. Replies
    109
    Views
    2,935

    Apparently Bob gets the memo now....:stirthepot: ...

    Apparently Bob gets the memo now....:stirthepot: :D

    Seriously Bob, I don't know where you get the idea that spammers are being shut down.
    Typically the thread gets locked at the most. The...
  5. With 304 at 25 KSI and MS at 40-50 KSI it should...

    With 304 at 25 KSI and MS at 40-50 KSI it should be pretty simple........

    That said, if you're bending other SS grades the numbers all change.... 301 (75 KSI), 440 (65 KSI), 17-4 PH (110 KSI).
    ...
  6. I can't speak as to the shearing part. But if you...

    I can't speak as to the shearing part. But if you look up the minimum yield strength, hot-rolled mild steel is about 40 KSI as opposed to 304 SS which is 25-30 KSI.

    That's why AR steels are so...
  7. 304 SS bends easier than mild steel IME. You'll...

    304 SS bends easier than mild steel IME. You'll be just fine.

    Just because it's stainless doesn't mean it's better..........unless it's from billet. :D :D
  8. Replies
    109
    Views
    2,935

    As much as I *may* agree with those of you...

    As much as I *may* agree with those of you complaining about Gordon, thermite, etc., that wasn't the intent of this thread. Not gonna go there.

    The question still is..."Why are the posted rules...
  9. Replies
    34
    Views
    879

    You're right, nowhere close to $20K. That BS...

    You're right, nowhere close to $20K.

    That BS gets spouted constantly......Just. Not. True.

    296467
  10. Replies
    28
    Views
    1,332

    There's more to that...... 296465

    There's more to that......

    296465
  11. Replies
    7
    Views
    384

    You could get a tool to match the tooth angle of...

    You could get a tool to match the tooth angle of the gear...14 degrees? Even if you were a degree or two off, by doing lots of passes at a very small WOC you'd get a decent finish.

    Harvey Tool -...
  12. Good grief. ...

    Good grief. https://ontarioconditions.com/forums/uploads/emoticons/default_c-n.gif

    Two pages and I haven't learned one new thing.

    Give the subject a break for pity's sake.

    It's like a...
  13. Replies
    109
    Views
    2,935

    Not the question. :crazy: For the record, I'm...

    Not the question. :crazy:

    For the record, I'm not trying to change anything. There's been a lot of whining on other threads by senior members on how this place has gone downhill.

    I merely...
  14. Replies
    15
    Views
    413

    And everyone wonders why I am pushing for more...

    And everyone wonders why I am pushing for more rules......:nutter:

    EDIT: Okay Doug, pushing for enforcing.....:D
  15. Replies
    109
    Views
    2,935

    Hence the question........:sulk:

    Hence the question........:sulk:
  16. Replies
    109
    Views
    2,935

    OT- Should forum rules be enforced more?

    With regard to spammers, free E-bay, and "troll threads" (YKWIM....26 pages recently :rolleyes5: ).

    Anyone else noticed the spam getting a bit thick lately..? And they get away unpunished...........
  17. Replies
    96
    Views
    6,649

    Here's a few more tricks I started using. (I...

    Here's a few more tricks I started using. (I can't take credit for all these, I learned about them on the SW forum.)

    :typing:

    - Hold Alt when dragging a drawing view. This allows you to select...
  18. Replies
    28
    Views
    1,231

    Start checking pressures at different locations,...

    Start checking pressures at different locations, kinda like chasing a loose connection with a multimeter.

    I would start on the pressure side of the pump, then after the system relief, then after...
  19. Replies
    6
    Views
    765

    I didn't know Larson was a PM member. Who'da...

    I didn't know Larson was a PM member.

    Who'da thunk......he knew him, our resident troll..!!
  20. Ahhhhh.............peace of mind. 296349 I...

    Ahhhhh.............peace of mind.

    296349

    I had left him off the list because he was contributing intelligently, unlike the others who are "on the blacklist* ".

    Things have...
  21. Replies
    20
    Views
    637

    No wonder people would rather go to "The Zone"...

    No wonder people would rather go to "The Zone" with their "CNC machiner" problems........:rolleyes5:



    >>OP, maybe if you call it a racist it will jump in guilt...??
  22. Replies
    20
    Views
    637

    Seems the OP needs this book: 296311

    Seems the OP needs this book:

    296311
  23. Replies
    53
    Views
    5,719

    Sorry, yoo is dumb spammer. Ve can see through...

    Seems useful.[/QUOTE]

    Sorry, yoo is dumb spammer. Ve can see through dat.

    :rolleyes5:
  24. Anyone using Centroid retrofit controls in a production shop?

    Several years ago I used to run an old Centroid-controlled toolroom mill for prototyping and low qty. runs.

    I almost forgot about them until I stumbled across their website: CENTROID CNC...
  25. Is it from sewer-grade billet...?? :skep:

    Is it from sewer-grade billet...?? :skep:
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4