Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gmc1724

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    1
    Views
    255

    T-Plus power on (warm up)

    Hi, I have a new-to-me SQT200MS with T-Plus control. When I switch it on from the transformer the green power light comes on on the controller (next to the monitor), when I press this nothing happens...
  2. Replies
    6
    Views
    500

    Thanks Phil, should it really be that noisey...

    Thanks Phil, should it really be that noisey though, it sounds like a broken air line.
  3. Replies
    6
    Views
    500

    Ok, so I ended up buying this machine, stills...

    Ok, so I ended up buying this machine, stills tons to get through but it looks like the air "leak" is something Mazak describes as an "air-curtain" which is piped into the bearing shroud behind the...
  4. Replies
    6
    Views
    500

    Cheers, I was worried it was maybe some kind of...

    Cheers, I was worried it was maybe some kind of air mist lube system for the spindle bearings:eek:
  5. Replies
    11
    Views
    1,246

    Vibratory Tumbling Advice

    Hi, I have 100's of small 316 stainless parts that I've tumbled to de-burr some sharp edges. The tumbling process has worked fine but there is a grey residue left on the parts that the customer has...
  6. Replies
    23
    Views
    1,650

    This is the way to go, I've done many transfer...

    This is the way to go, I've done many transfer line saddles over the years this way, these things run none-stop and I've never had a come back on them. 10hrs labour max for that job, we'd still...
  7. Replies
    6
    Views
    500

    SQT200MS Air Leak

    Hi, I've just been to look at a SQT200MS 1998 T+ lathe that's being sold at auction. Whilst inspecting the machine there was a loud air leak coming from the main spindle area, not knowing this...
  8. Replies
    6
    Views
    1,187

    Hi, could you please forward your pdf to...

    Hi, could you please forward your pdf to [email protected], I have a leaky kitagawa cylinder to go at next week. (can't get onedrive to open)
    Thanks...
  9. Replies
    0
    Views
    320

    Thread Insert Question

    Hi, for years now I have been using whit inserts for cutting both bspp and bspt threads, never had any comeback. I recently noticed that you can purchase inserts specifically for bspt threads, are...
  10. Replies
    8
    Views
    630

    I only use Mazatrol, it's so easy to program at...

    I only use Mazatrol, it's so easy to program at the control. I do have the iso option but after using Mazatrol for a while g-code just feels archaic on a lathe.
  11. Replies
    8
    Views
    630

    Also, tools are hard to find, make sure there's...

    Also, tools are hard to find, make sure there's lots with the machine...
  12. Replies
    8
    Views
    630

    I've had mine for about 4 years now, very robust...

    I've had mine for about 4 years now, very robust & accurate (will hold .01mm when warmed up). The main problem with these machines is the tool-changer set-up, you will have constant headaches with...
  13. Replies
    1
    Views
    335

    What does the lights indicate on the Freqrol...

    What does the lights indicate on the Freqrol drive, there's a vertical line of green led's that show the drive condition via a chart on the front panel?
  14. Replies
    24
    Views
    2,218

    Sounds like someone's F××ked-up on the quote to...

    Sounds like someone's F××ked-up on the quote to me, if he's on here asking can it be done then he probably didn't see it on the drawing when he took a shot at the quote. Unless it's his no.1 customer...
  15. Replies
    14
    Views
    1,390

    So I have a budget of 18mins per slot on these, I...

    So I have a budget of 18mins per slot on these, I know that's a lifetime but if I can get it down to half that without standing over the e-stop I'd be happy. Is the general consensus to use 2 flute...
  16. Replies
    14
    Views
    1,390

    I should just clarify one point, I'm not looking...

    I should just clarify one point, I'm not looking to break any records, I'm just looking for a stable process that can be left to nibble away on it's own.
  17. Replies
    14
    Views
    1,390

    Best method for slotting aluminium?

    I have a job coming up that involves producing an enclosed 10mm wide slot through 20mm thick aluminum plate, the slots are approx 400mm long and there's about 300off to machine. Machine is a Mori...
  18. Replies
    14
    Views
    1,165

    Hi, I have a ST20 with a similar arrangement...

    Hi, I have a ST20 with a similar arrangement apart from the coolant outlet and dowel positions are at separate positions. You should be able to back off the cap head screws, clamp a turning tool in...
  19. Replies
    21
    Views
    1,347

    Have you tried the chuck proximity switches on...

    Have you tried the chuck proximity switches on the chucking cylinder?
  20. Replies
    31
    Views
    3,039

    I'm not trying to dampen your spirits but I have...

    I'm not trying to dampen your spirits but I have a few observations about your potential start-up. I started at the age of 26, I'll be trading 20 years come February, it's made me a fair living but...
  21. Replies
    6
    Views
    594

    Sorry to be a pain noname777, the procedure...

    Sorry to be a pain noname777, the procedure involves disconnecting the servo belt, ballscrew encoder and bearing cap and thrust bearing nut at the top of the assy' then blocking up the turret to hand...
  22. Replies
    6
    Views
    594

    Is this the standard way of changing these...

    Is this the standard way of changing these bearings? Seems a bit extreme to have to use the ballscrew to press out the bearings, has anyone else tried this method?
  23. Replies
    6
    Views
    594

    Changing x-axis thrust bearing SQT18M

    Hi, after weeks of squealing and strange dimensional problems I finally decided to tackle changing the thrust bearing on our 1990 SQT T32. Thinking it would be a quick job but oh no. Has anyone here...
  24. Replies
    2
    Views
    482

    Obviously I have a very rare machine, or a rare...

    Obviously I have a very rare machine, or a rare name, not part of the gang eh?
  25. Replies
    2
    Views
    482

    SQT18 X-axis load

    Hi,

    I have a new to me SQT18 (T32-3 control), I'm getting some strange intermittent noise from the x-axis when it's travelling towards the chuck, away from the chuck it's fine. Can someone please...
Results 1 to 25 of 144
Page 1 of 6 1 2 3 4