Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: haastec

Page 1 of 27 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    49
    Views
    3,148

    There seems to be more going on here than just...

    There seems to be more going on here than just parameters. I won't say it's not possible, but I have never had a regen glow like that after initializing a machine or clearing bbu like you did.
    ...
  2. Replies
    49
    Views
    3,148

    Your voltage ranges are to low. The low voltages...

    Your voltage ranges are to low. The low voltages can cause random alarms and possibly problems such as yours. If you still have the problem after fixing the voltages, then I would suspect the...
  3. Replies
    26
    Views
    2,198

    Unfortunately, there is no way to backup the...

    Unfortunately, there is no way to backup the control itself. In the event of a system failure, the only thing to do would be to reload the machine software (dealer has this) and use your back up...
  4. Replies
    26
    Views
    2,198

    The thrust bearing is the bearing pack that...

    The thrust bearing is the bearing pack that supports the ball screw on the motor side. Usually when the thrust bearing starts to fail, you will notice that the axis will get a loud(ish) growl type...
  5. Replies
    7
    Views
    1,087

    There should be multiple e-stop connections on...

    There should be multiple e-stop connections on the I/O board, check to see if they are working properly (they may have a jumper installed). If they are, simply move the plug for the pendant e-stop...
  6. Replies
    9
    Views
    1,638

    Are you getting any alarms when this happens? If...

    Are you getting any alarms when this happens? If yes, what alarm(s)?
    Where exactly in the t/c process does everything stop and what exactly is happening at that time?
  7. Replies
    13
    Views
    2,315

    Thanks for everyone's input. I haven't had any...

    Thanks for everyone's input. I haven't had any machine time to do any additional testing, but essentially I am trying to identify which macro variable tells the machine which pallet is loaded so I...
  8. Replies
    13
    Views
    2,315

    Matsuura horizontal pallet change help

    I have a Matsuura h-Plus 300 with a 16i controller.

    My machine is a 2 pallet machine, is there a way I can tell the machine to load pallet A into the machine or Pallet B?

    What I would like to...
  9. For air lines, the push in fittings have been...

    For air lines, the push in fittings have been great in my experience, however, I have seen some machines where the push in fittings for the grease lube lines leaked grease. I just replace the push...
  10. Well done!

    Well done!
  11. The link you provided has instructions for belt...

    The link you provided has instructions for belt driven machine with or without gearbox. The section that includes the pressure gauge is for an inline spindle. Your pre-charge air pressure should...
  12. Agree with this and glad you got it figured out....

    Agree with this and glad you got it figured out.

    Not sure what year you have, but check out some procedures here: ...
  13. Three possible scenarios come to mind. Air...

    Three possible scenarios come to mind.

    Air leak at TRP piston
    Bad TRP solenoid
    or seized draw bar.
  14. Matsuura MC510 X-Axis cable replacement help

    I am trying to replace the X-Axis cable on my Matsuura MC510 machine and I am having some difficulty removing some cover panels.

    Can anyone offer some insight to the panel I have shown and any...
  15. Replies
    18
    Views
    3,609

    A little late to the party I guess! :D Enjoy...

    A little late to the party I guess! :D
    Enjoy the new machine.
  16. Replies
    12
    Views
    1,560

    See page 7...

    See page 7 https://www.haascnc.com/content/dam/haascnc/en/service/manual/service/english---vf-series-service-manual---1997.pdf
    I was going to suggest to much oil, but looks like you may have figured...
  17. Replies
    5
    Views
    1,093

    Look here...

    Look here https://www.haascnc.com/content/dam/haascnc/en/service/manual/service/english---horizontal-service-manual---1994.pdf

    As already noted, the biggest downfall of the HS is the pallet...
  18. Does your machine have a RECOVER button next to...

    Does your machine have a RECOVER button next to the POWER UP RESTART button?

    If it does, remove the tool from the spindle and carousel as described already, then press the recover button and...
  19. Replies
    18
    Views
    3,609

    Scanning the responses, I don't think anyone has...

    Scanning the responses, I don't think anyone has answered your questions regarding the differences of standard 8/10K vs 12/15K spindles.

    Primarily the 10K and less spindles use steel bearings
    12K...
  20. Replies
    20
    Views
    1,949

    Are you still struggling with this?

    Are you still struggling with this?
  21. Replies
    6
    Views
    1,118

    Resolution follow up. The problem ended up to...

    Resolution follow up.

    The problem ended up to be the cooling fans of the CPU unit. During my initial evaluation of the fans, I mistakenly said that the cooling fans were simple 2 wire fans. They...
  22. Replies
    6
    Views
    1,118

    This will probably be my task today. The fan for...

    This will probably be my task today. The fan for the spindle motor is running, but it is very dirty with a heavy build up of coolant sludge. Not very optimistic that it is the issue, but a clean...
  23. Replies
    6
    Views
    1,118

    No, all the fans so far have been basic 2 wire ac...

    No, all the fans so far have been basic 2 wire ac fans. No sensors that I have been able to find. Also, the fan that I did replace was an exact match.

    Still searching!
  24. Replies
    6
    Views
    1,118

    Matsuura MC510VG 1098 Fan Alarm help

    I have a Matsuura MC510VG with a Yasnac J300M control that I am having a problem with.
    I am getting a 1098 FAN ALARM OF CNC UNIT that does not clear. It was clearing for a couple of days, but now...
  25. Sorry to burst your bubble! Hopefully the final...

    Sorry to burst your bubble! Hopefully the final reveal will inspire some more excitement.
Results 1 to 25 of 662
Page 1 of 27 1 2 3 4