Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: jz79

Page 1 of 16 1 2 3 4

Search: Search took 0.01 seconds.

  1. so I mapped the error messages in French to 4 of...

    so I mapped the error messages in French to 4 of the possible custom error messages useable by the machine builder, they are markers #2955, #2980, #2925 and #2933, the problem is that when I do a...
  2. VW Golf mk7 with 1.4t petrol engine and DSG...

    VW Golf mk7 with 1.4t petrol engine and DSG gearbox (dual clutch manual) will get you 50-55mpg, and that is with all the extra safety and comfort included, if they would put this ICE in the mk1...
  3. I get messages in English, German and French on...

    I get messages in English, German and French on it, even though the language in parameters is set to English :D

    From reading the installation manual, it did mention that OEM upon completing the...
  4. I was hoping that I could disable those features...

    I was hoping that I could disable those features in machine parameters, but unfortunately there is nothing even regarding automatic/manual tool changes, just number of tools stored in memory, and...
  5. turns out that reading the manual very carefully...

    turns out that reading the manual very carefully helps sometimes, who would have thunk! :fight:

    a little bit further after the "For editing purposes, a program can be copied from EPROM into RAM",...
  6. Heidenhain TNC355, question regarding PLC program

    I have a Micron WF41 cnc mill with said TNC355 control and would like to have a look at the PLC program to make couple modifications regarding tool changer operation (disable it, and all related...
  7. Replies
    169
    Views
    6,345

    but, but they unplug their phone chargers when...

    but, but they unplug their phone chargers when they are not in use!
  8. Replies
    169
    Views
    6,345

    if you move the mass outwards from the center of...

    if you move the mass outwards from the center of rotation, then the rotation will slow down, it is quite basic, and best observed in figure ice skaters when they are doing their spins, move the leg...
  9. Replies
    169
    Views
    6,345

    around here we had the wettest December in...

    around here we had the wettest December in recorded history, and as water level rose back then, it hasn't returned to normal levels since
    Temperature wise - December usually would be around...
  10. you almost perfectly described the culture of...

    you almost perfectly described the culture of soviet era around here, the guy might have not even realized that he wasn't talking to a simple employee either

    that being said, there are tons of...
  11. Replies
    12
    Views
    867

    you're right, I didn't look carefully enough at...

    you're right, I didn't look carefully enough at it, jumped to conclusion thinking about something I'm familiar with
  12. Replies
    5
    Views
    530

    he is looking for the exact opposite of...

    he is looking for the exact opposite of passivation, passive layer is inert, it will not attract or react, activated surface on the other hand attracts other stuff, be it another metal - think...
  13. Replies
    12
    Views
    867

    google hall effect sensors, very common type of...

    google hall effect sensors, very common type of sensor used all over the world, from cars (wheel speed sensing, crank/cam shaft position sensing) to home security (door/window open positions), they...
  14. Replies
    19
    Views
    1,745

    this is a really bad idea for multitude of...

    this is a really bad idea for multitude of reasons, here are some:

    composites do not take point loads well, failure (in case of carbon fibers especially) will be sudden and catastrophic

    carbon...
  15. Thread: 45k$ Dining table

    by jz79
    Replies
    48
    Views
    3,562

    price was 45k not the cost, it is not really...

    price was 45k not the cost, it is not really polite to discuss the cost of such showcases of craftsmanship

    I'd be interested to see the techniques used to make the legs, just general curiosity,...
  16. Replies
    107
    Views
    7,314

    motorsport enthusiasts often take the original...

    motorsport enthusiasts often take the original aluminum core (new if available), cut off the formed up flange where the plastic caps are held in and just weld fabricated ends to the old core, any...
  17. Replies
    379
    Views
    94,261

    I believe it connects to this: 277743

    I believe it connects to this:
    277743
  18. Replies
    28
    Views
    1,577

    if it is mertric, then it won't be 24tpi but 1mm...

    if it is mertric, then it won't be 24tpi but 1mm pitch, M8x1.00 is the fine pitch M8 thread, that is the tap you need to use, 24tpi = 1.06mm pitch, on 1D worth of threads that is already error of...
  19. Replies
    3
    Views
    561

    this is too depressing to read, and the worst...

    this is too depressing to read, and the worst part about it - there is quite a big part of population that see these people as "making it", because they employed also a few honest people apart from...
  20. I can't speak for everyone, just from my...

    I can't speak for everyone, just from my experience regarding 6xxx series alloys, the main (or common among them) alloying element is Si in these, and the amount of it makes the difference (if all...
  21. Thread: Pull scraper??

    by jz79
    Replies
    17
    Views
    1,864

    this is the best vid I've seen that shows Swiss...

    this is the best vid I've seen that shows Swiss type scraping and tools:

    https://www.youtube.com/watch?v=TFCVO0fXW1k
  22. Replies
    8
    Views
    657

    In theory the witness sample should work, but it...

    In theory the witness sample should work, but it has to be the same stock of material for one, and racking has to be 'ideal' for both parts for them to behave the same way, what I mean by that is...
  23. Replies
    1,007
    Views
    91,891

    I tried Dykem hi-spot this morning on the...

    I tried Dykem hi-spot this morning on the differential gears I mentioned, and just couldn't get a good enough print, getting enough resistance between driving and driven side was also difficult with...
  24. 6063 and 6061 anodize basically with identical...

    6063 and 6061 anodize basically with identical results, 6082 (higher Si content) is where you can begin to see differences, higher Si makes the surface (even if polished to mirror) lose its luster,...
  25. any paint will produce rounded edge on corners,...

    any paint will produce rounded edge on corners, that will create the "parting line" effect

    anodizing will work for this, bright red is certainly possible, the only problem here might be with the...
Results 1 to 25 of 393
Page 1 of 16 1 2 3 4