Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ripperj

Page 1 of 42 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    6
    Views
    747

    Cool, thanks for posting it up. Sent from...

    Cool, thanks for posting it up.



    Sent from my iPhone using Tapatalk Pro
  2. Replies
    41
    Views
    2,321

    There are not too many days that go by without a...

    There are not too many days that go by without a amazon delivery here.

    Iím not especially proud of that, but Iím busy and if I have a couple minutes waiting between endless meetings.... a few...
  3. Replies
    115
    Views
    6,635

    I figured, I was just ball busting, although I do...

    I figured, I was just ball busting, although I do work with a guy thatís missing most of the fingers on one hand after losing a battle with a chain drive on some machine in a paper mill... that had...
  4. Replies
    115
    Views
    6,635

    Put the guard back on! I get nervous looking at...

    Put the guard back on! I get nervous looking at that :)


    Sent from my iPhone using Tapatalk Pro
  5. Thread: B&A Precision

    by ripperj
    Replies
    5,429
    Views
    837,510

    Those things are awesome, so much better than a...

    Those things are awesome, so much better than a ladder, throw the lights, all the tools , a soda and a five gallon bucket to sit on and up you go!
    They do move around when fully raised(the...
  6. Denis- I hope you donít think I was finding fault...

    Denis- I hope you donít think I was finding fault with your work.. the post was in jest :)


    Sent from my iPhone using Tapatalk Pro
  7. Replies
    17
    Views
    831

    And I guess I have a question? Looking at your...

    And I guess I have a question?
    Looking at your posts??
    Donít you have a 10Ē lathe and an Excello 602 ?
    Running off single phase?
    In your two car garage?

    You got a 7 figure revenue stream...
  8. Replies
    17
    Views
    831

    Because there is a metric butt ton of em. -...

    Because there is a metric butt ton of em.
    -
    This place makes money on traffic.
    -

    Take away the hobby guys and whose left? 3 cranky guys sitting around stroking each other and BSing about how...
  9. As a data point . My VMC 20 enclosure is 74.5Ē...

    As a data point . My VMC 20 enclosure is 74.5Ē wide by 46.3Ē deep
    Keith


    Sent from my iPhone using Tapatalk Pro
  10. Replies
    28
    Views
    4,842

    Itís a 10hp rotary unit. The math doesnít really...

    Itís a 10hp rotary unit. The math doesnít really work out for the vmc motor go. As you mention lots of specs mention 7.5hp. Several places in the manuals and the drive parameters on the machine...
  11. Replies
    10
    Views
    966

    I guess i May have misunderstood, I thought the...

    I guess i May have misunderstood, I thought the OP was buying a new one.
    If that one posted above is in nice shape , itís definitely worth $4k


    Sent from my iPhone using Tapatalk Pro
  12. Replies
    10
    Views
    966

    Import 16" engine lathe

    I too am not sure what you are actually asking
    I have a 30 year old 16Ē Kerry branded Namseon.
    I got it a couple years ago with very little use on it, the half nuts still had cosmoline on them.
    ...
  13. Replies
    26
    Views
    1,326

    Or even if you still want to do it, the skill may...

    Or even if you still want to do it, the skill may be no longer required.


    Sent from my iPhone using Tapatalk Pro
  14. Replies
    28
    Views
    4,842

    I have no experience with the PP, at the time I...

    I have no experience with the PP, at the time I needed power they were out of my budget .

    I ended up with a American Rotary 10 HP , still wasnít cheap, I think $1500ish with all the plugs...
  15. Charts say KDK tool post is too large for lathe? KDK 100 / 150 / 200

    Beefier is better with a toolpost, up to a point .

    I canít see the angles in the picture too well on my phone, but your pic shows a large post with a large holder and a big tool... all sticking...
  16. Replies
    1
    Views
    347

    Aloris Super-Precision 7-Piece Set AXA, 1-SET...

    Aloris Super-Precision 7-Piece Set AXA, 1-SET


    Sent from my iPhone using Tapatalk Pro
  17. Replies
    15
    Views
    1,129

    I had the same stuff that Bill is describing at...

    I had the same stuff that Bill is describing at my old house. I bought it 25 years or more ago. Mine was actually called Gutter Helmet. The top of the gutter is completely covered and water flows...
  18. I see affordable going out the window :) Keith ...

    I see affordable going out the window :)
    Keith


    Sent from my iPhone using Tapatalk Pro
  19. Thx Sent from my iPhone using Tapatalk Pro

    Thx


    Sent from my iPhone using Tapatalk Pro
  20. Mitutoyo, Starrett, Subitu/Dyer- OD and ID gages, calipers, micrometers, etc.

    On the Vee blocks-Are there any markings or paperwork that would indicate who makes them or how good they are?
    Thx
    Keith


    Sent from my iPhone using Tapatalk Pro
  21. I should try it before I put the new card in just...

    I should try it before I put the new card in just in case someone else runs into the same bind.


    Sent from my iPhone using Tapatalk Pro
  22. Iím going to call my machine BOAT Sent from...

    Iím going to call my machine
    BOAT


    Sent from my iPhone using Tapatalk Pro
  23. I seem to have some weird version, got off the...

    I seem to have some weird version, got off the phone with ITS and I should have the High Torque/ Rigid option like Ian posted.
    I bought version 96, Dan said thatís the one they recommend with -4...
  24. My wife had a Pathfinder, we had it along time...

    My wife had a Pathfinder, we had it along time and liked it.
    One day she comes home and says ďthe car is making a really loud horrible noise ď I pop the hood, donít see anything obvious, drive it...
  25. Denis Iím definitely interested in one. Nice...

    Denis Iím definitely interested in one. Nice work!
    Keith


    Sent from my iPhone using Tapatalk Pro
Results 1 to 25 of 1047
Page 1 of 42 1 2 3 4