Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: deadlykitten

Page 1 of 57 1 2 3 4

Search: Search took 0.02 seconds.

  1. if i may : there are dating sites for...

    if i may : there are dating sites for sentimentalism :)
  2. Replies
    13
    Views
    3,063

    12/0.00024 = 50000 10/0.0005 = 20000 1000/0.02...

    12/0.00024 = 50000
    10/0.0005 = 20000
    1000/0.02 = 50000 : this is a garant 468790 ( attached )

    i dont have the price for it, but after a quick on-line check, it is 280 euros

    it is a nice...
  3. hey bob :) here are some posibilities : ......

    hey bob :)

    here are some posibilities :
    ... editing acceleration + ipw
    ... improving transition between feed movements
    ... interpolation on entire toolpath

    i have messed with values that...
  4. hy / i try o avoid using 2 offsets for same tool,...

    hy / i try o avoid using 2 offsets for same tool, or should i say i try to avoid an operator editing 2 offsets for same tool

    if possible i use a single one, and i rely on insert precision to...
  5. hy / maybe you should check the ipw settings and...

    hy / maybe you should check the ipw settings and d values, so to speed up the drilling cycle for the okuma

    generally i use long hand drilling codes, because of situations when cycles could not...
  6. Replies
    10
    Views
    2,493

    drill in drill out tool is cleaned drill fast...

    drill in
    drill out
    tool is cleaned
    drill fast in
    reamer in
    tool out
  7. Thread: Roto Vise

    by deadlykitten
    Replies
    71
    Views
    12,550

    ... i would build the vice in it :) if something...

    ... i would build the vice in it :) if something happens, you can still mill out the integrated_vices and buy real ones

    also, you may consider including only the fix jaw, and buy 4 moveable jaws...
  8. i also have in mind future aplications for using...

    i also have in mind future aplications for using multiple_points on same insert, like making life easier for less experience operators, but so far is only an idea :)

    the reason for it is that...
  9. nice one Tom :) you are not a parasite ... in...

    nice one Tom :) you are not a parasite ...

    in this moment i have codes that use 2 different reference systems on same insert

    thus programing_point <> tool_senzor_point

    code is created with...
  10. Replies
    10
    Views
    2,493

    ok, just check on it and share what you think ......

    ok, just check on it and share what you think ...

    a technical drawing + actual setup / fixture + some ideas > is more than enough :)

    the idea of a double tool is not bad

    the target is a...
  11. Replies
    104
    Views
    7,080

    dmfTomB is like a gentle giant, he never said...

    dmfTomB is like a gentle giant, he never said nothing bad to nobody ... and here you refference him again
  12. Replies
    4
    Views
    1,452

    yes, i was reffering to Aland Islands, but is not...

    yes, i was reffering to Aland Islands, but is not 50km, but 500000000000000 km :)



    thx
  13. Replies
    104
    Views
    7,080

    in attached image, left: ... yellow :...

    in attached image, left:
    ... yellow : repetability for | Z_offset_thread_tool - Z_offset_turning_tool | measured at tool senzor
    ... blue : repetability for | Z_offset_thread_tool -...
  14. some guys are hot tempered, and this may put them...

    some guys are hot tempered, and this may put them in a bad situation :)

    is important to have patience and be able to locate the issues, especially with teenagers

    well, this does not mean that...
  15. Replies
    10
    Views
    2,493

    if possible, pls share : ... conditions for this...

    if possible, pls share :
    ... conditions for this operation ( drawing, tolerance, briefs, etc )
    ... quantity for parts and actual tools requirements
    ... actual tools / photo with actual setup
    ......
  16. Replies
    32
    Views
    5,579

    hy Fal Grunt / i use Blaser ... so far so good :)...

    hy Fal Grunt / i use Blaser ... so far so good :) lathe and mill

    any time i must wash something, i simply turn the coolant and wash it :)

    when i clean chucks, i put a rubber carpet inside the...
  17. Replies
    4
    Views
    1,452

    thats nice :) but were there servants ? i dont...

    thats nice :) but were there servants ?

    i dont know the english for such buildings, i also have been in a few

    they are for welcoming ( important ) guests for whatever reason :)

    big players...
  18. it is possible that Tom may keep generating...

    it is possible that Tom may keep generating programs on radius center, and an operator may measure the tool at lower-left corner

    this involves corelation between 2 different cutting edge origins
    ...
  19. is not complication / but a solution to operator...

    is not complication / but a solution to operator error prevention
  20. it is possible to have it both ways ... it...

    it is possible to have it both ways ... it requires an intermediate module between program and cnc interface :)
  21. hei Tom, i guess you can see there are more ways...

    hei Tom, i guess you can see there are more ways to skin the cat :)

    on a lathe with a tool setter, an operator will measure the tool more likely how your friend/aprentice suggested ...

    you...
  22. hy SND / just like ewlsey said, there is no need...

    hy SND / just like ewlsey said, there is no need for C axis :)

    however, you can use [ C axis ] or [ C axis + break ] or [ M19 ]

    be aware that M19 may not be as tough as expected, but it may be...
  23. hy tom :) if i get it right, this approach means...

    hy tom :) if i get it right, this approach means that insert coordinate system is located in the center of the insert radius :)



    this approach means that insert coordinate system is located at...
  24. Replies
    104
    Views
    7,080

    when threading at 0.1 to a shoulder, is good to :...

    when threading at 0.1 to a shoulder, is good to :
    ... know the destination / functionality of the final assemble
    ... take into consideration lathe size
    ... be aware of the downtime created into...
  25. Replies
    104
    Views
    7,080

    here, have another question : when threading...

    here, have another question :

    when threading at 0.1 to a shoulder, there is :
    ... [ roughing tool ] , that delivers the cilinder
    ... [ threading tool ] , that delivers the thread :)

    what...
Results 1 to 25 of 1402
Page 1 of 57 1 2 3 4