Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: naru

Page 1 of 7 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    10
    Views
    567

    That Tailstock is definitely home made, looks...

    That Tailstock is definitely home made, looks functional enough. If it lines up on center and is parallel to the ways then good on Ďem.

    Iím on mobile otherwise Iíd look up the serial for you, you...
  2. Replies
    3
    Views
    323

    Pay what I paid for it, $200. Itís a Yuasa chuck...

    Pay what I paid for it, $200. Itís a Yuasa chuck and it can ship it a Large Flat Rate via USPS. Comes with the camlock pins.

    Sold, pending payment.
  3. Replies
    3
    Views
    323

    Iíve got a 10Ē D1-6 direct mount 4 jaw, the jaws...

    Iíve got a 10Ē D1-6 direct mount 4 jaw, the jaws could use a regrind, but all of the components are still tight. No wear in the sliding surfaces between jaw and chuck. Just a bit of bell mouthing.
  4. Firstly, I would consult Ted Pflunger at...

    Firstly, I would consult Ted Pflunger at [email protected], heís the go-to for NOS or take off parts. Heís generally pretty good about having parts. If Ted canít help you I could make you one if you...
  5. Replies
    9
    Views
    621

    I meant chasing the thread. Taking down the...

    I meant chasing the thread. Taking down the diameter is trivial but the thread might be a bit more of a challenge. I know on my 13 the thread on the spindle comes to an abrupt stop at the shoulder....
  6. Replies
    9
    Views
    621

    Probably could, should be plenty of meat there....

    Probably could, should be plenty of meat there. Just remember you only get to fuck up once.
  7. Replies
    34
    Views
    2,364

    Well Iíve got one that does, one that doesnít. So...

    Well Iíve got one that does, one that doesnít. So Iíd say at least 1% of lathes have a tang slot in the tailstock. Give or take a few percent of course.
  8. Replies
    34
    Views
    2,364

    A lot of old south bend’s don’t have a slot for...

    A lot of old south bend’s don’t have a slot for the tang. The only benefit of a tang on your tooling is the ability to remove your tooling without a pickle fork. If there’s a way to remove tooling...
  9. Replies
    10
    Views
    430

    Wow thatís lucky!

    Wow thatís lucky!
  10. Replies
    10
    Views
    430

    I donít believe the fasteners are cast iron but I...

    I donít believe the fasteners are cast iron but I could be wrong. If they sheared Iíd look for damage to the gearing for the power cross feed and lateral feed. Thatís a lot of force to shear those...
  11. Replies
    10
    Views
    430

    Iím not 100% certain, youíd need to verify.. but...

    Iím not 100% certain, youíd need to verify.. but there is a complete double tumbler gearbox on eBay, I believe you can swap yours for that but it might require a different lead screw. Iím not really...
  12. Replies
    10
    Views
    430

    Youíll be hard pressed to find just the housing...

    Youíll be hard pressed to find just the housing for the gear box, youíll likely need to buy a complete box and swap out parts in better condition and sell off the rest or just use it as is and save...
  13. Replies
    16
    Views
    881

    Man I just donít even know where to start on...

    Man I just donít even know where to start on this! I really appreciate the very DRAMATIC editing work youíve done here. It really adds an appreciation for dramatically gazing into the distance in my...
  14. Replies
    10
    Views
    905

    well, you can get the tubing in 4' lengths for $1...

    well, you can get the tubing in 4' lengths for $1 from McMaster and 100 caps is $9, so it's cheaper to just buy from them (assuming it's not the only reason and ignoring shipping) than it would be to...
  15. Replies
    34
    Views
    2,364

    sizes above 1/2" are recommended to drill 1/32"...

    sizes above 1/2" are recommended to drill 1/32" under the final ream size. I think the rule is 3-5% final hole diameter should be left for reaming.
  16. Thread: Help with SB 117E

    by naru
    Replies
    12
    Views
    942

    I canít help you with the machine, on mobile and...

    I canít help you with the machine, on mobile and just donít feel like going through all of that.

    As for the 3 phase debacle.. there usually wouldnít be a plug on the machine regardless of 3 phase...
  17. Replies
    10
    Views
    784

    an appropriately sized RPC. They would recommend...

    an appropriately sized RPC. They would recommend you get at least double your highest HP motor, so 15HP for you assuming your lathe has the most ponies.
  18. Replies
    13
    Views
    1,102

    I didnít even notice the name, thanks for the...

    I didnít even notice the name, thanks for the purchase! If you can give me the part numbers for the gears Iíll take a look when I get home.
  19. Replies
    13
    Views
    1,102

    Well, it really depends on what is causing the...

    Well, it really depends on what is causing the play, if its side to side, or in the ways, make sure your gib is sufficiently tight with the adjustment screw which is on the cross slide to the upper...
  20. Replies
    13
    Views
    1,102

    If you want to get rid of some of that play in...

    If you want to get rid of some of that play in the cross slide, I can definitely help you with that!
  21. Replies
    13
    Views
    1,102

    Hi Eric, Iím on mobile or iíd Link it for you....

    Hi Eric, Iím on mobile or iíd Link it for you. But in the sticky topics in this sub forum one is asking for serial numbers. If you go to that topic, the second post has a link to Steve wells website....
  22. Thread: Doosan only forum

    by naru
    Replies
    12
    Views
    1,036

    Get rid of Baileigh while youíre at it!

    Get rid of Baileigh while youíre at it!
  23. The table is ridiculously heavy, have help and...

    The table is ridiculously heavy, have help and some way to lift it. Also the lead screw only goes in one way, well, itíll go, but one end is slightly different and will cause binding when running the...
  24. Replies
    14
    Views
    945

    Thatís the same machine as I have with a couple...

    Thatís the same machine as I have with a couple newer features. The 8 in CL8145B signifies that it is a toolroom version. According to literature, theyíre a more robust and precise version of the 13Ē...
  25. Replies
    14
    Views
    945

    Iíll start with the serial you provided. The TKX...

    Iíll start with the serial you provided. The TKX specifically would be T: 13Ē swing K: UMD/QCGB/friction clutch X: special spindle.

    The spindle would typically either be a 2 1/4Ē - 8 thread or...
Results 1 to 25 of 169
Page 1 of 7 1 2 3 4