Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: indychuck

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Replies
    9
    Views
    1,128

    Adjoining aluminum NO welding

    Im wanting to build an aluminum framed table (18H x 48L x 30W) that can hold a weight of about 300 lbs. This will be a fire pit table, so my joints cant be those composite T fasteners. I was...
  2. Replies
    2
    Views
    691

    They are special in that the pair needs to match...

    They are special in that the pair needs to match in weight and dimensions. A mis-matched pair is not desirable.

    These are indian clubs that are used for shoulder/wrist/elbow exercising and...
  3. Replies
    2
    Views
    691

    seeking wood turner - small project

    Any wood turners interested in making a pair of these?

    264922
  4. Thread: 6' lathe

    by indychuck
    Replies
    7
    Views
    2,047

    Jason, I'll send Dan a message, if I have no...

    Jason, I'll send Dan a message, if I have no luck, I'll send you a PM.

    Thank you,

    Chuck
  5. Thread: 6' lathe

    by indychuck
    Replies
    7
    Views
    2,047

    Does anyone know of anyone that has a wood lathe...

    Does anyone know of anyone that has a wood lathe that can turn a 6' piece of hardwood?

    Thank you,

    Chuck
  6. Thread: 6' lathe

    by indychuck
    Replies
    7
    Views
    2,047

    6' lathe

    Anyone have a 6' lathe they can turn a flag pole out of Ash for me?

    The bottom of the flag pole will be approx 2" diameter and the top will be around 1.625".

    I'll go over the detailed...
  7. Replies
    55
    Views
    4,271

    An oil-embedded thrust bearing was found by a...

    An oil-embedded thrust bearing was found by a machinist that customized it to the desired dimensions.

    All is good with the custom bearing/washer.
  8. Replies
    55
    Views
    4,271

    You're not force to read or reply, I don't feel...

    You're not force to read or reply, I don't feel one bit guilty of wasting your time. You're the only one wasting your time.

    L.E. Wilson shits on Dillon
  9. Replies
    55
    Views
    4,271

    Excellent advice, thanks for the pertinent info,...

    Excellent advice, thanks for the pertinent info, much appreciated!
  10. Replies
    55
    Views
    4,271

    It's not about getting it. It's simply about...

    It's not about getting it.

    It's simply about looking for someone to make a custom washer with the sizes recommended by the trimmer maker.

    You may go about life saying things are good enough,...
  11. Replies
    55
    Views
    4,271

    I can only elaborate based on the recommendations...

    I can only elaborate based on the recommendations of the manufacturer of the cutter. They advise placing a "properly sized washer" between the jam nut and the bearing wall. They do not sell a...
  12. Replies
    55
    Views
    4,271

    I'm one too - my wife will also attest. But I...

    I'm one too - my wife will also attest. But I assumed it would be an understood, that with the specific dimensions given, that any ole' washer wouldn't do.
  13. Replies
    55
    Views
    4,271

    This is a precision cutter and there can't be any...

    This is a precision cutter and there can't be any play on the ID, it unfortunately will be too "sloppy" of a fit.
  14. Replies
    55
    Views
    4,271

    Dualkit, you presumed correctly, I have not heard...

    Dualkit, you presumed correctly, I have not heard of McMaster.

    I have since contacted them and they do not make custom washers, the attached image is their email response. I assumed that was the...
  15. Replies
    55
    Views
    4,271

    This is horribly written, can you please try...

    This is horribly written, can you please try again in re writing "I don't think you can any quoted for that price."

    It makes absolutely zero intelligible sense.
  16. Replies
    55
    Views
    4,271

    Is anyone willing to make a couple washers with...

    Is anyone willing to make a couple washers with these dimensions for my Wilson trimmer? Fastenal, Lowes, Home Depot, etc. do not have anything with these dimensions. And custom washer fabricating...
  17. Replies
    10
    Views
    2,825

    Custom washer needed

    I would like a couple washers made and wondered if any members are available for hire on a small project.

    The washer measurements and material desired are as follows:

    Stainless Steel
    .060...
  18. Replies
    55
    Views
    4,271

    I received my cutter back from Ameristar today,...

    I received my cutter back from Ameristar today, would you prefer I send the cutter for a proper fit of the custom washer?
  19. Replies
    55
    Views
    4,271

    LE Wilson suggests a washer to be used to keep...

    LE Wilson suggests a washer to be used to keep the jam nut from digging into the bearing surface.
  20. Replies
    55
    Views
    4,271

    I'd be thrilled to pay that vs. the $83 quote I...

    I'd be thrilled to pay that vs. the $83 quote I received from Ameristar MFG.

    Let's hold off on more than one at this point, I want to make sure it will fit, or I can send you the cutter of what...
  21. Replies
    55
    Views
    4,271

    Custom washer(s) needed

    I would like a couple washers made and wondered if any members are available for hire on a small project.

    The washer measurements and material desired are as follows:

    304 Stainless Steel
    .060...
  22. Replies
    15
    Views
    1,272

    Good idea Steve, I'm going in horizontally, but...

    Good idea Steve, I'm going in horizontally, but the technique sounds like it may still apply.

    It's apparent that the drill method is definitely the hands down winner in terms of popularity on this...
  23. Replies
    15
    Views
    1,272

    Daniel, it will indeed be a through hole and I...

    Daniel, it will indeed be a through hole and I much prefer doing it by hand. Threading manually is no big deal, Im not on a time crunch and I like the positive feel while doing it by hand.
  24. Replies
    15
    Views
    1,272

    WTB quality taps

    In search of quality taps. A lot of upcoming work on docks requiring a lot of drilling and tapping of 1 / 4 inch galvanized. Most bolt sizes will be in the range of 1/4 thru 7/16.
    Investing in a...
  25. Replies
    17
    Views
    1,423

    Jack, I think I may have found a pair, but I do...

    Jack, I think I may have found a pair, but I do have another measuring device that I need. I'll touch base with you via pm.
Results 1 to 25 of 51
Page 1 of 3 1 2 3