Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: stevo1

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. The picture is of the 15series control...I used...

    The picture is of the 15series control...I used this control to show what I need it to do. The 16series will never change the code.

    I am actually really surprised that you guys normally don't see...
  2. Not true…I have the exact opposite. I have never...

    Not true…I have the exact opposite. I have never seen the line of code stay as it is written when the line of code is read and this is on all Fanuc’s

    See attached pic. 1st pic is of the program...
  3. Fanuc 16 does not display value of macro variable

    Just fired up one of our older machines I am doing a project on so I have a few settings to change before I get started.

    Ok so I have been thru the parameter manual a few dozen times now and I...
  4. Replies
    28
    Views
    3,452

    Paul, Using a decimal when passing variables...

    Paul,

    Using a decimal when passing variables will depend on the control. I have not come across a control yet (mostly Fanuc) that does not have a parameter setting that will specify how a value...
  5. Replies
    28
    Views
    3,452

    Paul...That should work fine. I would change the...

    Paul...That should work fine. I would change the G54B0 to G54B#2 so that you can use the same 09400 program for any degree you decide to program at.

    #5004 I believe will depend on which model...
  6. PM sent Stevo

    PM sent

    Stevo
  7. My apologize...I meant what are parameters...

    My apologize...I meant what are parameters 230-239 and 240-242 set to...

    Also I was not clear on the EOB (end of block)...that is why you are getting the alarm. In MDI mode you need to program...
  8. Your not screwed...that just means that you don't...

    Your not screwed...that just means that you don't have a macro call being executed with the T() command. You need to set these parameters to do so...but it will depend if you have the macroB option...
  9. One of the ways that I handle this is by using...

    One of the ways that I handle this is by using code within the tool change macro. Your machine may or may not be using a tool change macro depending on if someone set it up or if Mori is strictly...
  10. Replies
    739
    Views
    472,461

    Sticky: Sinha in post #224 wrote a good book call Custom...

    Sinha in post #224 wrote a good book call Custom MacroB programming.
    Amazon.com: CNC Programming using Fanuc Custom Macro B (9780071713320): S.K Sinha: Books
    I am not sure if there is a better...
  11. Replies
    17
    Views
    17,360

    I can’t believe that I missed that spec in the...

    I can’t believe that I missed that spec in the machinist book on the minor size. So yes the print and the spec are conflicting. I will not get clarification on what the customer wants. Even if I...
  12. Replies
    17
    Views
    17,360

    Bump…. I am still arguing this with others. I...

    Bump….
    I am still arguing this with others. I will give you a live example that is happening now.

    I have a part that calls a hole like so:
    .4531 +.01/-.005 DRILL THRU
    1/2-20 UNF 3B TAP THRU
    ...
  13. Replies
    17
    Views
    17,360

    I am less concerned of the hole being undersized...

    I am less concerned of the hole being undersized then I am of the clarification of what the minor diameter should actually be. It also is not always the same. Some holes shrink up and others do...
  14. Replies
    17
    Views
    17,360

    Thread minor diameter call out question

    I have not been around in some time now. I hope everyone is doing well.

    I have a controversial question for all regarding minor diameter on a thread call out. Let’s use a .625-18 UNF call out on...
  15. Replies
    739
    Views
    472,461

    Sticky: BS :icon_bs: It is not related to this topic at...

    BS :icon_bs: It is not related to this topic at all. It is just spam.

    Stevo
  16. Replies
    3
    Views
    3,191

    Thanks for the link I will save it. I did find...

    Thanks for the link I will save it.

    I did find my manual. I had to run home and I found it on 1 of my other 3 jumpdrives:willy_nilly: Got the parameter number changed and we are now back to...
  17. Replies
    3
    Views
    3,191

    I am looking for a Siemens Simodrive manual

    Hey guys I am looking for the manual for a Siemens drive model number 6SC 6508-4AA02. I need to make some position adjustments to the drive. I had the manual about a month back on PDF but placed it...
  18. Replies
    22
    Views
    12,762

    Thanks for the update. Check your PM box. ...

    Thanks for the update. Check your PM box.

    Stevo
  19. Replies
    6
    Views
    3,977

    X2. ABS encoders.....no alarm. You had one...

    X2. ABS encoders.....no alarm. You had one alarm to start but nothing before or after. Are you sure no one screwed with the machine and reset home?

    Stevo
  20. Replies
    32
    Views
    3,254

    Boris, I think you take this thread to your boss...

    Boris,
    I think you take this thread to your boss and show him that many others in your situation disagree with the interruptions and it is unproductive:willy_nilly:(it will go over like a fart in...
  21. Replies
    12
    Views
    8,944

    Thanks Gordon......good late night...

    Thanks Gordon......good late night chuckle.....well said. I have not heard that expression in some time now:D

    bialalyaka....Gordon was just poking but more info at the start would have cut out...
  22. Replies
    8
    Views
    4,334

    Your opinion was not stupid as all the confusion...

    Your opinion was not stupid as all the confusion does reside in that line of code but that is not what was dictating when to change the bar.


    Ok that didn’t help at first but I reread your post...
  23. Replies
    8
    Views
    4,334

    I looked at it quickly last night as well and...

    I looked at it quickly last night as well and more time today and it still doesn’t make sense to me on what he is trying to do or if there is missing info.



    Not true. At least not based on...
  24. Replies
    8
    Views
    4,334

    What is #560 set to. At a quick glance you could...

    What is #560 set to. At a quick glance you could be having a problem with floating point math. I am also assuming that #599 and #598 are set to null or 0 at the start of the program yes?

    A...
  25. Replies
    8
    Views
    3,057

    Tim, All the advice above is great advice. It...

    Tim,
    All the advice above is great advice. It will depend on the tolerance at first and then it will come down to how well you dial in your process for doing so.

    Most of the parts that I deal...
Results 1 to 25 of 444
Page 1 of 18 1 2 3 4