Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ifixcnc

Page 1 of 18 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    23
    Views
    1,256

    The only downside to SONY is that their stuff, is...

    The only downside to SONY is that their stuff, is only compatible with their stuff. So you end up buying all SONY accessories that wont work with any other brand.
  2. Replies
    32
    Views
    1,342

    We went thru that nightmare last year. The...

    We went thru that nightmare last year. The unknowns that turn into additional costs, cant be forecast. We hit bed rock at 3 feet. The tank needed to be 15 foot deep. Pneumatic jack hammer on an...
  3. Replies
    9
    Views
    853

    To do it right, the machine will need to be...

    To do it right, the machine will need to be completely disassembled. New turcite glued on, and then scraped. A Puma 240 may not be worth all that. Show a picture of the strip.
  4. [QUOTE=alphonso;3367114] "Called Sauter". ...

    [QUOTE=alphonso;3367114]

    "Called Sauter". Who? Where? I haven't been able to find a contact other than Germany.

    Sauter North America Inc.

    1116 Centre Rd.
    Auburn Hills, MI 48326
    USA...
  5. Sounds like Monarch may have a turret position 1...

    Sounds like Monarch may have a turret position 1 prox.
    Look at your electrical manual.
    The Sauter usually has an led on the back of the encoder to allow for timing the #1 position.
    If the machine...
  6. Replies
    1
    Views
    237

    Try TOLL FREE : (888) 976-6789 ADDRESS : 5788...

    Try

    TOLL FREE : (888) 976-6789
    ADDRESS : 5788 Schaefer Ave., Chino, CA 91710
    E-MAIL : [email protected]

    3 hours behind MI
  7. Replies
    1
    Views
    259

    See this thread. Parameters for YCM-TC-2...

    See this thread.
    Parameters for YCM-TC-2
  8. Replies
    3
    Views
    498

    If ii did not do this before, it seems like an...

    If ii did not do this before, it seems like an clean up and fluid change out, would be the ticket. Some how the fluid has changed characteristics, or some thing on the conveyor is plugged up.
  9. Replies
    108
    Views
    5,603

    With all due respect to Major General Smedley...

    With all due respect to Major General Smedley Darlington Butler,
    who ran for Senate as a Republican in 1932.
    Things have changed a bit in 87 years.
  10. Replies
    4
    Views
    560

    Try YCM USA Address 20540 Belshaw Ave...

    Try

    YCM USA

    Address
    20540 Belshaw Ave Carson, CA 90746 USA
    Website
    Error
    Tel
    1-310-735-8610
  11. Replies
    26
    Views
    1,307

    Did you have the M19 problem before the parameter...

    Did you have the M19 problem before the parameter reload?
  12. Replies
    6
    Views
    526

    HiTrol control is 840D Siemens hardware, but it...

    HiTrol control is 840D Siemens hardware, but it has Hyundai software that tried to make it act like a Fanuc.
  13. Femco USA – HIGH QUALITY CNC MACHINES SINCE 1958...

    Femco USA – HIGH QUALITY CNC MACHINES SINCE 1958

    Is the part supplier here in the US.

    The Durga is an bit of an handful as I recall. The service guys at Femco may have some tips for you.
  14. Replies
    1
    Views
    279

    The shifting Bimba cylinders, and air blast for...

    The shifting Bimba cylinders, and air blast for the spindle, air lines are likely crossed.
  15. Replies
    9
    Views
    734

    With machine powered down, hold in the P & Cancel...

    With machine powered down, hold in the P & Cancel buttons. Turn the machine on and stay on those keys until the machine is done starting. Try to reference, If that wont work get your parameter book...
  16. Replies
    4
    Views
    633

    My encoder is a bit different, but it does have...

    My encoder is a bit different, but it does have an position 1 led, for turret timing. My guess is that you are OK.
  17. Replies
    6
    Views
    590

    technician said that was the best he could get ...

    technician said that was the best he could get
    Would likely indicate that is an after comp measure. As mentioned that is good for an older machine, but if the comp value is large the tool will move...
  18. Replies
    6
    Views
    590

    Have you set the backlash parameter to 0? If not...

    Have you set the backlash parameter to 0? If not you are measuring the after compensation value.
  19. Replies
    11
    Views
    871

    Nikken tables are expensive and worth it. Trying...

    Nikken tables are expensive and worth it. Trying to save on oil that will give you years of service, is not an savings. Mobile gear 627 is top shelf gear lube, if you must cut corners one could put...
  20. Replies
    9
    Views
    725

    A lot of different conveyors are available....

    A lot of different conveyors are available. Depending on the particular chip you are producing, they can work well, or not. The high end machine's have some nice options, like the Mayfran Consep for...
  21. Replies
    37
    Views
    3,694

    My opinion is that unless you have some very...

    My opinion is that unless you have some very special iron. an retrofit is more of an head and wallet ache than it is worth. The used machinery market is full of good value on semi current machines....
  22. Replies
    4
    Views
    481

    the red led lit all of sudden Is that the...

    the red led lit all of sudden
    Is that the feedhold light? Next to the cycle start.
    A picture would help.
  23. If the draw bar or gripper is hanging up, or the...

    If the draw bar or gripper is hanging up, or the actuation mechanism is gone wrong. YES.
    Any change in the sound that you are accustom to, is a sign of something wrong.
    Try a stethoscope (or an...
  24. Replies
    30
    Views
    2,186

    "We had some issues that we finally figured was a...

    "We had some issues that we finally figured was a faulty cable linking pcb to io board "
    I would go over the cabling and parameters with a fine tooth comb.
    As others have said, an runaway on...
  25. Take a flashlight and a mirror and watch the...

    Take a flashlight and a mirror and watch the action of the gripper.
    Clamp a tool and set up an indicator on the flange, then pry with a big screwdriver between the tool flange and the spindle nose....
Results 1 to 25 of 433
Page 1 of 18 1 2 3 4