Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: plastikdreams

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Seals can dry out as well as the powder from the...

    Seals can dry out as well as the powder from the cutting process can dry on parts and really rip up seals. Plus the resistivity of the water gets way out of spec.

    On the older mits (beige) units...
  2. Don't rule out mits machines. Very good quality,...

    Don't rule out mits machines. Very good quality, excellent service, and great controls.

    Everything implmex has said is spot on!
  3. Replies
    27
    Views
    1,007

    The one engineers reply was, if it's too lose...

    The one engineers reply was, if it's too lose we'll use Teflon tape...it's out of my hands now.
  4. Replies
    27
    Views
    1,007

    For sng here's picture from my mh for tap drill...

    For sng here's picture from my mh for tap drill sizes for American thread forms

    315763
  5. Replies
    27
    Views
    1,007

    Pretty much...that's why I asked. And if you...

    Pretty much...that's why I asked. And if you actually READ my op I had an answer I was just double checking. :rolleyes5:



    Sure lol like I said I have 0 experience with bsp :)
  6. Replies
    27
    Views
    1,007

    Bsp wasn't even remotely in the equation...I've...

    Bsp wasn't even remotely in the equation...I've never even threaded anything bsp. Funny thing is, they brought me 2 taps and a similar part that would thread into the block. The nut on the part...
  7. Replies
    27
    Views
    1,007

    1/8 bsp straight.

    1/8 bsp straight.
  8. Replies
    27
    Views
    1,007

    It can be a shitshow here one engineer from dept...

    It can be a shitshow here one engineer from dept a specifies something being made for dept b but then an engineer from dept b says its supposed to be something else...then we can't get the 2 of them...
  9. Replies
    27
    Views
    1,007

    Ended up being 1/8 bsp thread lol.

    Ended up being 1/8 bsp thread lol.
  10. Replies
    27
    Views
    1,007

    I didn't see 28 in my mh v28. But looks like the...

    I didn't see 28 in my mh v28. But looks like the numbers match up. Looks like they are going to use a nut to tighten up some threaded suction cups to hold vacuum. I guess npt wasn't good enough...
  11. Replies
    27
    Views
    1,007

    Thanks guys...I'm waiting for some clarification...

    Thanks guys...I'm waiting for some clarification on a couple things...
  12. Replies
    27
    Views
    1,007

    The book shows 3/8-27 and R drill...how much you...

    The book shows 3/8-27 and R drill...how much you wanna bet the engineer wrote the wrong number lol.
  13. Replies
    27
    Views
    1,007

    I do, I didn't even think to look there...way to...

    I do, I didn't even think to look there...way to make me feel like a dumbass lol

    :)
  14. Replies
    27
    Views
    1,007

    Tap drill for 3/8-28 tap

    I have to tap 2 holes 3/8-28. All the drill charts I've found do not have this size. Per the ghuring site it recommends .340 for the hole size at 75%, which is basically a letter R (.339) drill. Does...
  15. Replies
    30
    Views
    9,571

    With each pass you vary the speed and power...

    With each pass you vary the speed and power settings this helps with recast and surface finish. I like to turn adaptive control off so the machine travels at a steady pace and leaves no marks from...
  16. Replies
    2
    Views
    386

    In Mastercam I usually use a pocketing routine...

    In Mastercam I usually use a pocketing routine with true spiral leaving 5k in x and y. As lock nut said add a countour at the end as a spring pass...or 2 I usually measure in between.

    I'll also...
  17. Replies
    10
    Views
    439

    Was that supposed to be Connecticut?

    Was that supposed to be Connecticut?
  18. I'd search nfpa and see what it says.

    I'd search nfpa and see what it says.
  19. Short of running your finger inside the taper...

    Short of running your finger inside the taper before inserting a tool and/or cleaning the taper on the tool holder, there's not much one can do. Of course don't blow/wash the machine out without a...
  20. Replies
    6
    Views
    532

    In regards to the title...maybe try to liven...

    In regards to the title...maybe try to liven things up a bit, nobody likes a boring finish. :)

    Thanks, I'll be here all weekend
  21. Where in ne pa?

    Where in ne pa?
  22. I disagree 100% with the above. What does it...

    I disagree 100% with the above. What does it matter if he's spent 5 days looking or none at all? A question is a question, that's what the forum ultimately is here for other than discussion. Who are...
  23. Replies
    15
    Views
    869

    Doesn't matter what anyone thinks really...if it...

    Doesn't matter what anyone thinks really...if it suits your needs that's all that counts. Unless there was a safety issue, which I don't see any.
  24. Replies
    14
    Views
    515

    Ohh that's a good catch!

    Ohh that's a good catch!
  25. Replies
    17
    Views
    562

    That guy is a hack on his best day...

    That guy is a hack on his best day...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4