Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BuffDan

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    16
    Views
    782

    M20x2.5 bolts for my MSG-200M Manuals are...

    M20x2.5 bolts for my MSG-200M
    Manuals are available on ebay..
  2. Replies
    16
    Views
    782

    The drive cable needs to be undone by loosening...

    The drive cable needs to be undone by loosening cable nut on right side of table. The table then just lifts up. Heavy table, so 2 guys..
  3. Replies
    16
    Views
    782

    Also, remove table and balls for safe...

    Also, remove table and balls for safe transportation, dont transport grinder with table/balls installed.. You could also lift table, remove balls, and place rubber rod where the balls were.. Make...
  4. Great job! Thanks for letting us know

    Great job! Thanks for letting us know
  5. Clamping rear toolpost.. hydraulic tracer... Per...

    Clamping rear toolpost.. hydraulic tracer... Per my AA manual
  6. Replies
    6
    Views
    618

    Do you have a part number to share ?

    Do you have a part number to share ?
  7. Replies
    6
    Views
    618

    Here's a post from the past: harrison m300...

    Here's a post from the past: harrison m300 question
  8. Replies
    6
    Views
    1,320

    Post what you have.. He might want them. I'll let...

    Post what you have.. He might want them. I'll let him know

    It is a great saw.. Built like a tank.. I kind of have sellers remorse. :)
  9. Replies
    6
    Views
    1,320

    Sold...................

    Sold...................
  10. Replies
    6
    Views
    1,320

    DoAll C-916 Horizontal Band saw -$850

    Runs good
    Cuts straight
    Just installed new blade
    Down feed cylinder works fine- hold in place and control down feed speed
    Running on VFD, so I never tested the internal controls

    Buffalo NY...
  11. Replies
    7
    Views
    1,178

    His is a "H" model, hydraulic.. The manual...

    His is a "H" model, hydraulic.. The manual version has model M
  12. Replies
    9
    Views
    1,842

    296052 This is my setup. Plastic hood, easily...

    296052

    This is my setup. Plastic hood, easily replaceable, section of unistrut to raise and lower, and slotted aluminum plate to move in/out from wheel. The dust collector is a Torritt I picked up...
  13. Replies
    32
    Views
    3,099

    Bar z Industrial Development Products | Hotshot...

    Bar z Industrial Development Products | Hotshot Ovens
  14. I could sure use that microscope light!! PM...

    I could sure use that microscope light!!
    PM incoming.
    Thank you!!
    Dan
  15. 291362I use a plastic hood that Grizzly sells.....

    291362I use a plastic hood that Grizzly sells.. $10.. I''m not in a production mode, so will last for me
  16. hood, chute, scoop....

    hood, chute, scoop....
  17. Replies
    25
    Views
    3,088

    Sent pm, but couldnt add image for some...

    Sent pm, but couldnt add image for some reason290219
  18. Replies
    25
    Views
    3,088

    I'd be interested in wheel arbors such as290196

    I'd be interested in wheel arbors such as290196
  19. Replies
    11
    Views
    1,481

    icarbide was making them, but I dont see them...

    icarbide was making them, but I dont see them anymore
  20. how much ?

    how much ?
  21. looks like Rockwell 11 YouTube...

    looks like Rockwell 11
    YouTube
  22. 288692 The magnets popped right out, they were a...

    288692
    The magnets popped right out, they were a press fit.
    They sure are weak..
    I ordered some neodymium 1/2x1/8 magnets.. They will fit inside the inner brass shields. I will probably have to...
  23. I haven't used it because the magnets don''t...

    I haven't used it because the magnets don''t hold it in place very well.. I have cleaned it and painted since the attached photo.. I view this as a project, learning, etc. I believe it can be a...
  24. Replies
    6
    Views
    818

    Sent me scam PM also

    Sent me scam PM also
  25. Thanks for the input... The magnets have 2 brass...

    Thanks for the input... The magnets have 2 brass shells and 2 steel for the magnet.. I'll have to get one out, hopefully intact..
    Not sure if I need to replace with magnet that has outer brass...
Results 1 to 25 of 143
Page 1 of 6 1 2 3 4