Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: homebrew.357

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    20
    Views
    3,689

    Well tried my pull through reamer with lots off...

    Well tried my pull through reamer with lots off oil and came out spot on, I ground it to .446" and the bore came out at .449", so happy with that leaves a bit for polishing. This is with 12/15 ...
  2. Replies
    20
    Views
    3,689

    OK, got two 12mm straight flute reamers for $58,...

    OK, got two 12mm straight flute reamers for $58, just a bit over size but can grind them to the diameter I want and set up on my pull rod. I may jut be getting there, Cheers and thanks...
  3. Replies
    20
    Views
    3,689

    Looked them up and don`t export J G S precision,...

    Looked them up and don`t export J G S precision, would love one from them. Will have search on eBay, I get my gun drills from there, delivered in five days to my door. But every time I put in bore...
  4. Replies
    20
    Views
    3,689

    Yep, that's another way I could at it, I've just...

    Yep, that's another way I could at it, I've just reamed out a barrel that I cut the rifling to deep. The bore was .463" I wanted .458" so did what you did, ground a .480" milling cutter to fit in my...
  5. Replies
    20
    Views
    3,689

    AARRR, all comes clear, well I`ll have to wait...

    AARRR, all comes clear, well I`ll have to wait for a reply, thanks for that, we kiwi`s aren't in your time slot.
  6. Replies
    20
    Views
    3,689

    Do you have a email for them other than...

    Do you have a email for them other than [email protected]ge.com, I'm getting no answers. Have opened a account with them and found a 45-70,.450" reamer but pull or push?. And at $180.50 for...
  7. Replies
    20
    Views
    3,689

    That would be Pacific tool and gauge, ok I have...

    That would be Pacific tool and gauge, ok I have sent them a email and what I`m looking for is a pull through .450" reamer, my drill leaves a hole of .444" so that's only .006" to finish size. Length,...
  8. Replies
    13
    Views
    3,900

    I may be lucky, I`m looking for a pull through...

    I may be lucky, I`m looking for a pull through .450" finish reamer, 33" long, and as you have your fingers on a lot just thought I would check to see, thanks Homebrew.357.
  9. Replies
    20
    Views
    3,689

    Bore reamers

    Hi Guys, I`m looking over there for a pull through bore reamer, not a chamber reamer, and having a hard job of finding one and to get an answer from my Emails. I`m in New Zealand so is extorting a...
  10. Replies
    13
    Views
    7,182

    Hi guys, I've just received two bonded diamond...

    Hi guys, I've just received two bonded diamond wheels, I only use them for sharping T/C tipped gun drills and never use them for grinding steel, this can stuff them up . Another thing I`m trying to...
  11. Replies
    11
    Views
    1,146

    You are probably right they come from Asia, I...

    You are probably right they come from Asia, I don`t know where mine came from. I have asked Mt Roskill to see if they can get them.
  12. Replies
    11
    Views
    1,146

    They are thin plated and can't be redressed, the...

    They are thin plated and can't be redressed, the front and back edge have lost the cut, only the front side is working. I know a company in China, Kosuperhard make them but thought there was one in...
  13. Replies
    11
    Views
    1,146

    Nickel plated diamond wheels

    Hi guys, I have been using a small diamond plated wheel to sharpen my T/C gun drills and its starting to wear out, can't remember where I got it from. So trying to find a supplier in US that makes...
  14. Replies
    21
    Views
    8,786

    This is hobby barrel making so I'm are not in...

    This is hobby barrel making so I'm are not in mass probation, I've found that using water soluble oil as a cutting fluid for barrel drilling and reaming is no good, I have Fuchs Ecocool 400, when...
  15. Replies
    20
    Views
    5,536

    Well if you have lots of hydraulic rams why not...

    Well if you have lots of hydraulic rams why not set up to button rifle, could be a lot easier as you have lots of comeinhandy bits.
  16. Replies
    20
    Views
    5,536

    The best way to get rid of the chrome would be to...

    The best way to get rid of the chrome would be to grind it off, other than that it can be stripped in a caustic solution making the shaft the anode with a battery charger. Should be something on the...
  17. Replies
    20
    Views
    5,536

    No, The cutter only cuts when it is pulled...

    No, The cutter only cuts when it is pulled through the barrel, when it comes out chips are cleared and the large nut at the end is pushed out, this pulls the inside ramp back so cutter can go down...
  18. Replies
    20
    Views
    5,536

    Hi John, K, Your lucky, when I did the build for...

    Hi John, K, Your lucky, when I did the build for my two rifles I took pic`s as I build them, so if you go to www, " Making a Sharps barrel on my lathe" you will get my thread of making the Sharps...
  19. Replies
    20
    Views
    5,536

    Range report, Went to the range and tried the new...

    Range report, Went to the range and tried the new .50 muzzle loader barrel out at 50m with .490" patched ball and 65grs 2f Swiss black powder. Sights are on line horizontally but 7 1/2" low, last two...
  20. Replies
    20
    Views
    5,536

    Yep, You have got to have a hobby, keeps the old...

    Yep, You have got to have a hobby, keeps the old brain working and got mine going with making a front sight to fit on the barrel. Milled the V slots and used a flip up back sight I had laying around....
  21. Replies
    21
    Views
    8,786

    Yep, There`s more than one to do this, I got a...

    Yep, There`s more than one to do this, I got a star .50 gundrill from eBay, new for $75 so I can drill .50 barrels. When I got it I found it had two oil holes in the tip but drilled hole ok, but only...
  22. Replies
    20
    Views
    5,536

    I have made a slider with ali blocks that slides...

    I have made a slider with ali blocks that slides on the lathe bead ways, this is wound up and down vie a loop of bike chain. Top of the loop is bolted to the slide. On top of it is a square ali...
  23. Replies
    20
    Views
    5,536

    Hi Mihti mate, I`m in west Auckland, That is the...

    Hi Mihti mate, I`m in west Auckland, That is the Awakeri black powder range, went down for a fun steel shoot. I`m with the A K L deer stalkers and shoot at their riverhead range in the forest. My...
  24. Replies
    20
    Views
    5,536

    Hi, I got the plans on Ebay, The Quigley down...

    Hi, I got the plans on Ebay, The Quigley down under 1874 Sharps it`s the original 1871/74 plans, nine sheets measured, complete full size drawings all parts. 24x36. The only part I did not make was...
  25. Replies
    32
    Views
    7,169

    Well I`v found that it`s the hole size in the gun...

    Well I`v found that it`s the hole size in the gun drill that controls oil presser, I`v only a Nissan car steering pump and at 1,500 rpms I get 200/300psi. This is ok if you are drilling a .45cal...
Results 1 to 25 of 185
Page 1 of 8 1 2 3 4