Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Vladymere gr

Page 1 of 27 1 2 3 4

Search: Search took 0.01 seconds.

  1. Upgrading to a new Southbend may be the way to...

    Upgrading to a new Southbend may be the way to go.

    Weather you get a replacement Grizzly, this Grizzly repaired and returned or a new Southbend please let us know how the new one works out for...
  2. Replies
    35
    Views
    3,005

    I'm sorry for your loss. I thought a disaster...

    I'm sorry for your loss.

    I thought a disaster was when a female pilot backs into a propeller.

    Vlad
  3. Replies
    15
    Views
    1,703

    john.k Can you source this information about...

    john.k

    Can you source this information about the US Model of 1917 being called a Pattern 17 in Brittan?

    Vlad
  4. Replies
    15
    Views
    1,703

    What is a P17? I am familiar with the British...

    What is a P17?

    I am familiar with the British Pattern 14 or P14 and the US Model of 1917 but I've not heard of a P17 or Pattern 17.

    Vlad
  5. Replies
    28
    Views
    2,564

    The OP bought a lot of 250 or 300 bottles, his...

    The OP bought a lot of 250 or 300 bottles, his words. He should have a receipt for this purchase which would include the purchase of the military tanks. This should be sufficient proof of...
  6. Fellows, Thank you all to those that...

    Fellows,

    Thank you all to those that responded.

    Friday 01/18, with the help of my daughter in law, I did get the gas pack moved into location. The location was from the top of my concrete...
  7. Regarding the V ways, the two outside V ways are...

    Regarding the V ways, the two outside V ways are for the carriage to ride on and are the ones I would use for leveling. The inside V way and the flat way are the tail stock ways.

    Vlad
  8. Replies
    8
    Views
    584

    If it is like a Bridgeport then you can have...

    If it is like a Bridgeport then you can have sealed bearings that require no lubrication or, as installed by Bridgeport, open race bearings that do require lubrication. With the open race bearings...
  9. Good information on the bucket gentlemen. I...

    Good information on the bucket gentlemen. I don't know if it is a quick release or not or if it has a hook or not. I was not planning to hank it from on of the teeth though but a loop of chain over...
  10. Fellows, I thank all of you who have replied....

    Fellows,

    I thank all of you who have replied.

    With the information provided I think I will be able to get the job done.

    I have e-mailed Kubota to verify if the mini excavator I plan to rent...
  11. Rigging A Gas Pack For Lifting, Neophyte Needs Advice

    Fellows,

    I am in need of advice. I am a home hobbyist who will be fitting a gas pack to my shop. I do have some experience with the HVAC world but am not a professional yet I should be able to...
  12. Replies
    62
    Views
    16,041

    Well done RoboChair! Vlad

    Well done RoboChair!

    Vlad
  13. Replies
    38
    Views
    2,330

    zerocool, You have gotten some very good...

    zerocool,

    You have gotten some very good advice in the thread, including that your shopsmith does not meet Practical Machinist guidelines.

    For the most part the guys on this board will answer...
  14. Other Tray-Top owners may also be interested in a...

    Other Tray-Top owners may also be interested in a new nut. I can't imagine who (cough, cough).

    Vlad
  15. Well fellows, It is not a done deal but I may...

    Well fellows,

    It is not a done deal but I may have found a replacement spindle for my lathe. Hope springs eternal. If am able to get it I will update this post later to let those that may be...
  16. Fellows, First let me thank all of you for...

    Fellows,

    First let me thank all of you for your advice.

    I didn't bother with photos. I did use a sharpie and mapped the high and low spots on the L00 cone. The high and low spots where...
  17. Replies
    21
    Views
    2,748

    DT38K, I sent a PM to you. I am interested in...

    DT38K,

    I sent a PM to you. I am interested in the spindle from your Tray Top lathe. Please PM or e-mail me. My e-mail address is in the PM I sent.

    Vlad
  18. Replies
    10
    Views
    1,443

    Nice looking chuck. A good brand with a...

    Nice looking chuck. A good brand with a reputation of well made. Just don't over extend the jaws and clip the bed or carriage and you will be golden.

    Vlad
  19. gmach10, I do have a manual. No clutch in this...

    gmach10, I do have a manual. No clutch in this fellow except in the carriage.

    Thermite, "Do you know how to map "precession" of the first-failing element as the error excursion point migrates...
  20. Replies
    1
    Views
    942

    How do I add a video to a thread?

    How can I add a short video to a thread? I sometimes see them in threads. "I thouhgt if I linked it to photobucket but photobucket will not allow me to upload the file as it is an unsupported file....
  21. What is wrong with my 12'1/2" x 40" Cincinnati Tray Top Spindle?

    I am a home hobbyist with a Cincinnati Tray Top lathe that I bought from my employer. Please don't refer me to the home hobbyist machinist site.

    When I am cutting as I get closer to the chuck I...
  22. Replies
    21
    Views
    2,748

    DT38K, PM sent about spindle availability. ...

    DT38K,

    PM sent about spindle availability.

    Vlad
  23. Replies
    8
    Views
    1,617

    I think you made the right choice, based on the...

    I think you made the right choice, based on the specs.

    Vlad
  24. Replies
    25
    Views
    1,524

    Color me jealous. Damned nice work. Vlad

    Color me jealous. Damned nice work.

    Vlad
  25. Replies
    18
    Views
    1,053

    I have a multiple 3 phase devices in my shop. ...

    I have a multiple 3 phase devices in my shop. All 2HP or less. One RPC feeding a 3 phase breaker box runs all of my devices. The RPC is home built and is using a 5HP motor. No grunt when devices...
Results 1 to 25 of 674
Page 1 of 27 1 2 3 4