Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BROTHERFRANK

Page 1 of 35 1 2 3 4

Search: Search took 0.01 seconds.

  1. Brother has done that already with the Speedio...

    Brother has done that already with the Speedio F600 for larger tools and heavier cuts. Their engineers are relentlessly working to expand their products capabilities. They are also not trying to...
  2. SK stands for Super Kool (aid). Just kidding....

    SK stands for Super Kool (aid). Just kidding. Actually the SK, has a lower taper angle than ER which should give higher clamping force combined with more bearing contact area on the tool shank. The...
  3. 65 lbs seemed like a lot to me too. SK is...

    65 lbs seemed like a lot to me too. SK is supposed to hold better than ER. I was surprised when EagleMike pulled a 1/2" end mill out of a new Maritool SK16 with a 1/2" collet. Cut was fairly light...
  4. Was that a Nikken SK or a Maritool? As I recall...

    Was that a Nikken SK or a Maritool? As I recall but I might be mistaken, Maritool recommends 65 lb/ft torque on that collet nut!
  5. Hey Greg. Was that with Dual Contact or standard...

    Hey Greg. Was that with Dual Contact or standard BT30? Are Diamondbacks 45 degree helix? I like trying to use lower angle helix such as 37 or 40 degree for less pull out force. Getting those last...
  6. ID Plate on the machine and the power spec in the...

    ID Plate on the machine and the power spec in the brochure both state 10.4 KVA power requirement for the High Torque Brother machines. At 220V 3 phase that works out to 27.3 Amps. If your not pushing...
  7. Are you familiar with PM member SRTMike? He is in...

    Are you familiar with PM member SRTMike? He is in the Mass. area also. He speaks very highly of his local Yamazen rep.. Mike has a S700 and recently was involved in the purchase of a R650 pallet...
  8. 99.99% operator error

    99.99% operator error
  9. That is a relative statement. 1/4" may be a huge...

    That is a relative statement. 1/4" may be a huge sidewall for someone doing tiny medical parts with .010" endmills, but practically microscopic to someone running large parts that require a crane to...
  10. Replies
    18
    Views
    1,329

    Hey Ken. Did you get the Robo in?

    Hey Ken. Did you get the Robo in?
  11. Replies
    4
    Views
    1,591

    This machine is sold and shipping out this week....

    This machine is sold and shipping out this week. Thank you.
  12. Replies
    14
    Views
    1,872

    Have you checked out Schunk? Super solid. We use...

    Have you checked out Schunk? Super solid. We use them frequently.
  13. Replies
    30
    Views
    6,727

    OK. PM me your contact info and I will get it to...

    OK. PM me your contact info and I will get it to the local team first thing in the morning. Happy Father's Day everyone!
  14. Replies
    30
    Views
    6,727

    Are you closer to Cinci or Cleveland? I can help...

    Are you closer to Cinci or Cleveland? I can help you get in touch with your local service team. They are really good and are there for you.

    A note to Brother users or future users:

    Tech tip of...
  15. Replies
    30
    Views
    6,727

    Yes. You map an output to a condition you want,...

    Yes. You map an output to a condition you want, say Green. The Green output will only come on when the machine is cycling. You tie that output to a 24V dc relay coil. Then you run your pressure...
  16. Replies
    25
    Views
    1,785

    Now you're really cookin' with gas Pete. Teaching...

    Now you're really cookin' with gas Pete. Teaching those boys right too! Congratulations and glad all went smoothly getting it in the shop. Can't wait to hear how your parts are coming off of it. One...
  17. It seems to me that maybe the amplifier/drive...

    It seems to me that maybe the amplifier/drive itself needs to be programmed/set up. As I recall, every once in a while when I installed rotaries, they would send me a drive that wasn't set up...
  18. Replies
    30
    Views
    6,727

    You don't need the plc to do this. Just tie your...

    You don't need the plc to do this. Just tie your pressure switch to a mappable input. There are choices for EXERxx. External Alarm. You can set the stop level and the message to be displayed in the...
  19. I was going to suggest calling Koma Precision...

    I was going to suggest calling Koma Precision (Tsudakoma) 800-249-5662

    They should be able to get the parameters, even if they have to contact the mothership in Japan. The parameters are supplied...
  20. That's great. Let us know how it goes when you...

    That's great. Let us know how it goes when you get a chance.
  21. Kills the servos.

    Kills the servos.
  22. Those are great machines. Top of the line in it's...

    Those are great machines. Top of the line in it's day. You have too many issues for simple help on here. You need to invest in a service call to get the alarms sorted and some training in my opinion....
  23. Replies
    112
    Views
    4,926

    Hey Pete. I am sure you will look back and think...

    Hey Pete. I am sure you will look back and think it was one of your best decisions. For the record, I did not sell Pete anything and I only receive the satisfaction of knowing I helped someone. I did...
  24. That's the U-drill adapter. Takisawa stocks it...

    That's the U-drill adapter. Takisawa stocks it typically and available through Yamazen parts dept.
  25. Replies
    112
    Views
    4,926

    I'll add to that. We should do a test cut and...

    I'll add to that. We should do a test cut and show them what a High Torque Dual Contact machine will do for them. We have the S500, S700. S1000 and pallet machines in stock with that configuration.
Results 1 to 25 of 863
Page 1 of 35 1 2 3 4