Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 6 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    25
    Views
    2,604

    I sold machines like your in Montana last year,7...

    I sold machines like your in Montana last year,7 inch shaper sold for $800.00 out of state (man drove 1000 mi to get it) 1 1890s vert mill quite rare $750.00, 1930s Horz mill $300.00....Phil
  2. Replies
    17
    Views
    549

    If there is not enough iron drop to a #3...Phil

    If there is not enough iron drop to a #3...Phil
  3. Replies
    17
    Views
    549

    Get a mt 5 to mt 4 adptr, insert the mt5 into the...

    Get a mt 5 to mt 4 adptr, insert the mt5 into the lathe and mark,and see how much to cut down, then cut the mt 5 tapor until it is a little proud of the spindle, and use a #4 center ...Phil
  4. I use them to make 3 ball check valves for steam...

    I use them to make 3 ball check valves for steam engines...Phil
  5. Use a drill to rough out the slot just stay a...

    Use a drill to rough out the slot just stay a little undersize and link the holes a little bit...Phil
  6. Replies
    24
    Views
    1,189

    Make it...Phil

    Make it...Phil
  7. Well I dont know metric electric motor specs but...

    Well I dont know metric electric motor specs but I can give you American... 7.5 hp, best if it is 2 pole (3600) 480 volt star (Y)winding to run a 480 rpc, every motor will be a little different as...
  8. I still get gooogle, hate the hell out of...

    I still get gooogle, hate the hell out of them....Phil
  9. The winter was not the problem, once the engine...

    The winter was not the problem, once the engine warmed up it would keep you nice and warm. Took about ahour to melt the ice so the cluchs worked good. Summer was the bad time, 120f in the cab and the...
  10. Give me a call, let me know how and who is going...

    Give me a call, let me know how and who is going to move it to the back door and pay for the crane, what tooling you want, and how soon this will happen and If it has to be taken apart and I will...
  11. Replies
    17
    Views
    1,184

    Older that 70 years, close to 100. My first lathe...

    Older that 70 years, close to 100. My first lathe was a b&e gearhead 1922...Phil
  12. I use a Mart parts washer, a old dish washer...

    I use a Mart parts washer, a old dish washer would work , Is your wife home??If not ....Phil
  13. That the charge to look at it....hi hi....Phil

    That the charge to look at it....hi hi....Phil
  14. These old gals were my bread and butter for 30...

    These old gals were my bread and butter for 30 years, every logger had at least a 22b, 30b or the 54b for high line logging, I made 1000s of parts for the BE sure miss them,But not the grease...Phil
  15. Replies
    5
    Views
    396

    Its a job for a pro, you have only 1 chance to...

    Its a job for a pro, you have only 1 chance to get it right, Have any real good machinest friends?...Phil
  16. 2 speed 480 volt motor, you dont have any good...

    2 speed 480 volt motor, you dont have any good quick fixes, If it was mine I would use a 240/ 480 2kw transformer 1 phase and a 480 volt 3kw vfd to make 3 phase witch would also give you a veri...
  17. Replies
    54
    Views
    2,751

    With my monarch type 62 and 2- 4 jaw chucks( one...

    With my monarch type 62 and 2- 4 jaw chucks( one the front ,standard, and one one the rear , my ad on) I can rough 4 inch 4140 with a .5 cut .025 feed 180 rpm. chip fly like popcorn...Phil
  18. 96x 72y 48z .005 .008 .010 .015 ....Phil

    96x 72y 48z .005 .008 .010 .015 ....Phil
  19. Replies
    15
    Views
    1,148

    Ya the damm power co, cheap, cheap, cheap, Open...

    Ya the damm power co, cheap, cheap, cheap, Open delta is better than y 208 but vfd,s dont like it, and you will have a voltage/ amp unbalance. It only takes 1 more wire and transformer to give you...
  20. Replies
    54
    Views
    2,751

    P I A , they tend to get jammed with fine chips...

    P I A , they tend to get jammed with fine chips when you are boring, real pain to clean up, not any better than 3 jaw....Phil
  21. Replies
    10
    Views
    707

    Just use a push broach with a aluminum back up...

    Just use a push broach with a aluminum back up washer on the bottom of the stack, should reduce the crushing for the plastic on the bottom...Phil
  22. Replies
    1,557
    Views
    91,133

    There will not a big rush to buy China,s stuff......

    There will not a big rush to buy China,s stuff... might help US builders...Phil
  23. With the stick out of the #4 center his tail...

    With the stick out of the #4 center his tail stock looks re-cut to fit the #3 knock out slot....Phil
  24. Replies
    10
    Views
    543

    Look at door interlock switch for dirt, grime, or...

    Look at door interlock switch for dirt, grime, or adjustment, or maybe loose heaters...Phil
  25. The G&L head is bolt on, and has a fixed ring...

    The G&L head is bolt on, and has a fixed ring gear that drives the head, 4 speeds and feed out or feed in and you can start or stop the feed with the head spinning, and with the right attachment cut...
Results 1 to 25 of 144
Page 1 of 6 1 2 3 4