Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: machineit2

Page 1 of 27 1 2 3 4

Search: Search took 0.05 seconds.

  1. Not intending to piss anyone off, but if you...

    Not intending to piss anyone off, but if you don't know how to add a little code at the end of the program to bring the table where you want it you need to stop studying your CAD-CAM program and open...
  2. Thread: TM series

    by machineit2
    Replies
    5
    Views
    618

    I have a 96 and a 97 and they are both still...

    I have a 96 and a 97 and they are both still going strong.
  3. If you want, set a video camera up to film it and...

    If you want, set a video camera up to film it and then watch it. You will be able to see if the pump cycles and that will tell you if the pump is bad or the switch is bad. That is what I did.
  4. My old girls, 96 & 97, have been on Vactra 2...

    My old girls, 96 & 97, have been on Vactra 2 since new. No issues so why change now.
  5. I always run a 100% rapids unless I am testing a...

    I always run a 100% rapids unless I am testing a program out. Not ever a problem.

    As for G00 vs G01, the difference is in the way the machine moves between points. If you are moving 10 inches in...
  6. Replies
    10
    Views
    816

    The prgrm/convrs button!!!!!!!!!!!!!!!!!!!!!!! ...

    The prgrm/convrs button!!!!!!!!!!!!!!!!!!!!!!! Upper left button under the DISPLAY section. When you hit the edit button it comes up in the reduced size mode with "F" functions enabled, when you...
  7. Replies
    10
    Views
    816

    Hit the program button, toward the center. It...

    Hit the program button, toward the center. It toggles between editing screens.
  8. Replies
    12
    Views
    993

    No offense, but you need to get out of that...

    No offense, but you need to get out of that mindset. Will not serve you well in the future.

    Mike
  9. Replies
    12
    Views
    993

    In almost any situation, mill or lathe, the...

    In almost any situation, mill or lathe, the finish face surface on a part IS Z zero.
  10. Replies
    11
    Views
    952

    You can home the machine without resetting the...

    You can home the machine without resetting the machine. Just power up restart as normal, alarms will be canceled when done.

    Mike
  11. Replies
    17
    Views
    1,246

    How much space do you have to cool and is this an...

    How much space do you have to cool and is this an insulated building, how many window to the outside?
  12. 40 X 60, 18 foot walls, insulated was about...

    40 X 60, 18 foot walls, insulated was about $36,000, plus about $16,000 for erection and about $20,000 for foundation. I put a second floor on half, so 3600 Sq Ft total floor space. Near Knoxville,...
  13. Replies
    4
    Views
    1,297

    I bought my HS-300 from a gentleman on eBay and I...

    I bought my HS-300 from a gentleman on eBay and I know he has some parts Brothers. This is one of his listings.

    He might be able to help you

    Mike

    B-axis for Brother HS-70A wire edm, CNC...
  14. Campbell-Housfeld is a good BRAND of compressor,...

    Campbell-Housfeld is a good BRAND of compressor, but that is a small one there. You need a larger tanked model and higher kick-in and kick-out pressures. A nice big compressor from Home Depot or...
  15. Not sure you should try if you don't have the...

    Not sure you should try if you don't have the exact equipment and know how to use it. It has to flow SLOWLY!!!!!

    Be careful.
  16. It sounds good to have the door out, but you end...

    It sounds good to have the door out, but you end up have to push and pull hard to get them installed and I would imagine it is easier to do in the machine. It is good to have a little help too. All...
  17. He is correct. For many years I ran two VF-2's,...

    He is correct. For many years I ran two VF-2's, a Hardinge CNC lathe, saws and a manual mill on a 20 HP phase convertor that was on a 40 amp breaker. I now have two converters, but I am moving to...
  18. Replies
    5
    Views
    567

    One more time, how do you SET the numbers?

    One more time, how do you SET the numbers?
  19. Which unit do you actually have, there are a...

    Which unit do you actually have, there are a couple.
  20. Replies
    11
    Views
    983

    Should not worry about the last G03, as the codes...

    Should not worry about the last G03, as the codes are different for left and right hand threads, G84 Vs G74. The code determines the spindle direction.
  21. Replies
    5
    Views
    567

    How are you setting them?

    How are you setting them?
  22. Replies
    28
    Views
    3,251

    It's not delivered yet? Can you cancel the...

    It's not delivered yet? Can you cancel the purchase?
  23. Replies
    28
    Views
    2,525

    I use these guys, never a problem. Zaritron...

    I use these guys, never a problem.

    Zaritron
  24. Replies
    10
    Views
    806

    I ran two VF-2's and a Hardinge CNC lathe with a...

    I ran two VF-2's and a Hardinge CNC lathe with a 20HP rotary phase converter for years on a 40 amp breaker.
  25. Glad it's up and running!

    Glad it's up and running!
Results 1 to 25 of 666
Page 1 of 27 1 2 3 4