Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cyclotronguy

Page 1 of 44 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    16
    Views
    716

    It's been awhile since I looked at the drawings,...

    It's been awhile since I looked at the drawings, as I recall is was 65 degrees, thanks for the heads up.... I should re-visit that sooner rather than later.

    AB Tools is about 20 min from the house!
  2. Ted I have a couple of the #1's and #2's The...

    Ted

    I have a couple of the #1's and #2's The last one came to me about 5 years ago. Cincinnati grinders was able to supply the correct manual by serial number for very reasonable $ as well as a...
  3. If what you have is what I think it is, those are...

    If what you have is what I think it is, those are not parting blades they are Armstrong facing blades and pretty obscure.
  4. Replies
    16
    Views
    716

    jdub63 Rich and myself too and probably...

    jdub63

    Rich and myself too and probably others. Any chance of the basic dimensions of the notches?
  5. Replies
    16
    Views
    716

    rke[pler Yeah those "stoppers" I back...

    rke[pler

    Yeah those "stoppers" I back engineered one Al then ordered up some durabar to make the rest. Have yet to make the cutter for the dovetail, but it's on the too-doo list
  6. Replies
    16
    Views
    716

    Again a pretty simple part, we just need a...

    Again a pretty simple part, we just need a "print". And that said the folks at Monarch are pretty unpredictable on pricing. I needed a set of stoppers for a 10ee turret.

    The set up fee to...
  7. I bought a couple of Kennedy boxes from Fastenal...

    I bought a couple of Kennedy boxes from Fastenal about 10 years ago... the sales-lizard insisted on a cash sale... no mystery there!
  8. Replies
    16
    Views
    716

    Hard to tell, it might be reasonable $, and then...

    Hard to tell, it might be reasonable $, and then again maybe not. That said if we had a DWG, and a stick of O-1, the rest is EZ.
  9. Replies
    16
    Views
    716

    Rich What do the lads in Sidney Ohio charge for...

    Rich
    What do the lads in Sidney Ohio charge for a stop rod?
  10. Replies
    13
    Views
    592

    I have a very old (1950's) if I were to guess...

    I have a very old (1950's) if I were to guess "Victor" mixer. Inside it looks like one of those epoxy mixing nozzles, followed by a sintered bronze screen. I've used it to mix welding gasses. I...
  11. Rocheleau (sp?) in Canada makes Lista like boxes...

    Rocheleau (sp?) in Canada makes Lista like boxes that can be configured however you want at less than LISA / Vidmar prices I have a couple of their 24" x 18" boxes, they are very nice. I put an...
  12. I've done very little HY-100 but lots of HY-80...

    I've done very little HY-100 but lots of HY-80 for the Govt and always with humorless inspectors at your shoulder. And for decades both materials were well guarded secrets. For pressure vessels...
  13. Replies
    43
    Views
    10,094

    I have a shop equipped Lixi hammer, their...

    I have a shop equipped Lixi hammer, their smallest. Delrin head on one side, brass on the other, prolly a 8 oz hammer at most. R-8's pop out with a tap from the brass head, literally 4" of free...
  14. Replies
    8
    Views
    516

    If you have one of the Enco made in India...

    If you have one of the Enco made in India clones..... run away. I bought one new from Enco. The fit and finish and the hardwood box was lovely. And that's where the love affair ended. The feed...
  15. Replies
    2
    Views
    273

    COLT45 I'm with you on all counts. My issue...

    COLT45

    I'm with you on all counts. My issue specifically is that the "poop sheets" for the Tang Grip blades all show that they are to be mounted in a holder with 8 degrees of back rake built into...
  16. Replies
    2
    Views
    273

    Aloris BXA-77

    Aloris claims the 7 / 71 / 77 holders are all compatible with Iscar cut-off blades. There is no back rake built into a Aloris 71 / 77. As I look at the Iscar catalog for their Tang Grip tools, it...
  17. Replies
    3
    Views
    565

    Without photo's You're not going to glean much...

    Without photo's You're not going to glean much attention.
  18. You might be able to make that happen, not...

    You might be able to make that happen, not however with preferred settings. I suspect the results would be less than you'd hoped for.
  19. Replies
    3
    Views
    453

    SIP6A I have seen one of the small H-S...

    SIP6A

    I have seen one of the small H-S surface grinders, the spindle appeared well done: A belt drive affair similar to what we are used to seeing on a lot of the older North American tool...
  20. Shouldn't be difficult that is the off shore...

    Shouldn't be difficult that is the off shore answer to the Cinc #2, everyone form Acer to Yuasa has put their badge on one. And as with the Cinci #2, the machines used are dirt cheap, the tooling of...
  21. Replies
    2
    Views
    522

    If I had to guess I would think it came from a...

    If I had to guess I would think it came from a vintage universal grinder, Possibly B&S
  22. Hey unknown, possibly cogent but maybe not. As I...

    Hey unknown, possibly cogent but maybe not. As I am sure you know, diodes only conduct when the voltage on their junctions is greater than what's downstream from them. As a result with a cap input...
  23. Ahh, I've been in your ditch and I think I know...

    Ahh, I've been in your ditch and I think I know the way out. It's not the bench grinder it's the general purpose stone they come with, the bond is way to hard and the abrasive mostly non friable. ...
  24. Sir Tormek is generally considered a hobby...

    Sir

    Tormek is generally considered a hobby machine. That said; As apprentices we were all expected to learn how to offhand grind drills and lathe tools. The learning curve for hand dressing...
  25. Replies
    10
    Views
    798

    IF the deceased owner was from Reno NV, there...

    IF the deceased owner was from Reno NV, there might be history to be had.
Results 1 to 25 of 1099
Page 1 of 44 1 2 3 4