Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: AARONT

Page 1 of 44 1 2 3 4

Search: Search took 0.03 seconds.

  1. Thread: OT--Riots

    by AARONT
    Replies
    108
    Views
    3,352

    Nobody cares what you do with "real men". Thats...

    Nobody cares what you do with "real men". Thats some pretty odd flexing on your part. The internet tough guy routine is played out.
  2. Thread: OT--Riots

    by AARONT
    Replies
    108
    Views
    3,352

    You hope a thread about Riots doesn't come up and...

    You hope a thread about Riots doesn't come up and get over 4300 posts, so you decided to start one? :dopeslap:
  3. Replies
    24
    Views
    1,023

    Sometimes you'll notice dimensional changes after...

    Sometimes you'll notice dimensional changes after a machine warms up. If the tool looks good, comp it and keep making chips.
  4. Replies
    105
    Views
    4,257

    To damn near anything else?

    To damn near anything else?
  5. Thread: Bore Problems

    by AARONT
    Replies
    12
    Views
    742

    What's the diameter of the bar and length of the...

    What's the diameter of the bar and length of the bar hanging out? It could be deflecting.
  6. Draw it up and note it just like you would any...

    Draw it up and note it just like you would any other length.
  7. Replies
    11
    Views
    728

    How did your boss tell you to inspect them? I'm...

    How did your boss tell you to inspect them? I'm ASSuming you're just tapping. So just make sure your drill size is right and tap is right and move on. Just get the ok from the boss first so it...
  8. Are you running Allied inserts? It looks like...

    Are you running Allied inserts? It looks like those are the recommended numbers for that insert.(page 32)If the length of drill is more than 3xD you're going to have to slow it down on feed and...
  9. Replies
    6
    Views
    637

    Are you using an M88 for coolant? Are these new...

    Are you using an M88 for coolant? Are these new drills? There could be chips packed in the coolant holes if they're used.
  10. Of course. The Z is only 30". You've got 54" more...

    Of course. The Z is only 30". You've got 54" more to go.
  11. Get them a notebook and make them write stuff...

    Get them a notebook and make them write stuff down. Review the notes so you know it makes sense. I find just having people write things down helps them remember. Then if they don't remember, they...
  12. Someone's watched Minority Report too many...

    Someone's watched Minority Report too many times...
  13. Replies
    17
    Views
    1,515

    Ours show the alarm after the machine has been...

    Ours show the alarm after the machine has been off for over 48 hours.

    Typically a spindle warmup won't go up and down but gradually just increase rpm's. Then there's also moving your table in x,y...
  14. Replies
    17
    Views
    1,515

    If the machine hasn't been powered on in I...

    If the machine hasn't been powered on in I believe 48hrs, then that message pops up.
  15. Thread: Reamer Trouble

    by AARONT
    Replies
    14
    Views
    660

    Do you have a 3 jaw chuck you could hold on to?...

    Do you have a 3 jaw chuck you could hold on to? Along with whats been said, feed faster. General rule of thumb is half the speed twice the feed on a reamer as you would
    a drill. 500 rpm is fine for...
  16. Replies
    64
    Views
    3,697

    Strap that to the table. Rough and finish...

    Strap that to the table. Rough and finish everything except the outside profile. Come back and rough the outside profile within .005-.008"" of the table and .005" of the wall. Finish the wall. Punch...
  17. Replies
    64
    Views
    3,697

    It's not "because it's a Haas". Do you really...

    It's not "because it's a Haas". Do you really think those tabs are more rigid than the machine? GTFOH
  18. Replies
    6
    Views
    577

    Slide hammer?

    Slide hammer?
  19. Thread: Thread Gages

    by AARONT
    Replies
    7
    Views
    553

    There is nothing wrong with that. Especially if...

    There is nothing wrong with that. Especially if it's something for internal use. But if there is going to be a decent quantity of parts, it may be worth while to get some good gages made. I have had...
  20. Go to desired location. Load spot, then spot,...

    Go to desired location. Load spot, then spot, rotate, spot, rotate, etc. Next, load drill, drill, rotate, drill, rotate, etc. Load next drill, drill, rotate, drill, rotate, etc. Next, load tap, tap,...
  21. Replies
    21
    Views
    1,499

    Post pictures. It is possible to have a "blotchy"...

    Post pictures. It is possible to have a "blotchy" looking anodize finish.

    To me it sounds like you need a new anodizer.
  22. Replies
    11
    Views
    668

    We used our Haas post for our Fadal(down at the...

    We used our Haas post for our Fadal(down at the moment) and it ran well besides changes for tapping(G84.1). I can't remember if it's in format 1 or 2 though. I'd run it high and see if there are any...
  23. Replies
    38
    Views
    4,824

    I don't think it would matter much if holding the...

    I don't think it would matter much if holding the diameter. If you're holding the ends and using a facemill, you would want to feed into the hard jaw. Depending on the tolerance needed for the part....
  24. Replies
    11
    Views
    954

    I'm guessing it started based off metric...

    I'm guessing it started based off metric dimensions. 151.5mm = 5.9646" then spec a tolerance of +/-.5mm? As I have jaws that measure from 5.960"-5.976"
  25. Replies
    48
    Views
    2,222

    Because different opinions are scary!

    Because different opinions are scary!
Results 1 to 25 of 1091
Page 1 of 44 1 2 3 4