Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. On many machines ,Schaublin and Weiler to mention...

    On many machines ,Schaublin and Weiler to mention 2 ,a clamp can be used to keep the chuck on when turning in revers
    Attached a picture of one
    339780
    The sleeves in the flangebody you do not...
  2. Replies
    27
    Views
    1,483

    That pallet is too flimsy to be helpfull I...

    That pallet is too flimsy to be helpfull
    I prefere decent straps over bolts
    Drilling machine is always a bitch to transport
    Horizontal you need a special big enough pallet and blocks to keep...
  3. Yes .......................... Peter

    Yes ..........................

    Peter
  4. Remove the key and rotate the quill perhaps ?? ...

    Remove the key and rotate the quill perhaps ??

    Peter
  5. We put the 2 heaters in serie and tested again...

    We put the 2 heaters in serie and tested again After a much longer time as before it tripped once more
    So it did have some effect at least
    But.....
    After further inspection we discovered that it...
  6. Replies
    7
    Views
    706

    Buy buy buy buy

    Buy buy buy buy
  7. The thermal overload is in the 220volts 50 hz...

    The thermal overload is in the 220volts 50 hz supply line So that is where I measure
    Peter
  8. I measured less as 2 amps with a clamp on amp...

    I measured less as 2 amps with a clamp on amp meter Running at different speeds or starting had little to no influence
    Peter
  9. Replies
    7
    Views
    706

    It all depends on the price If it is GBP2500 or...

    It all depends on the price
    If it is GBP2500 or less

    BUY BUY BUY

    If under GBP 5000
    If it runs decent and all works sort of
    Buy

    Over GBP 5000
  10. I optioned that already :D Thanks Peter

    I optioned that already :D



    Thanks
    Peter
  11. That is why these are made from 16% Crome steel ...

    That is why these are made from 16% Crome steel
    And even then

    Peter
  12. Replies
    4
    Views
    318

    And you can buy new charts from Schinfa Peter

    And you can buy new charts from Schinfa


    Peter
  13. Contactor Overload Relays on 2 phases

    I have a contactor overload relay Telemecanique LR2 D13 1.6 to 2.5 Amp
    It is protecting a 220 V 2Ph circuit board to drive a DC motor
    We measure a load of 1.8 amps with a clamp on At least clearly...
  14. That 2 coloured wire (green/yellow) is ground ...

    That 2 coloured wire (green/yellow) is ground Theother ones are the 3 hot wires

    Peter
  15. Replies
    6
    Views
    591

    On most milling ma hines you have a long r...

    On most milling ma hines you have a long r spindle and a short nut On this one you have half a nut that is long but with a big diameter 60 - 70mm from memory The spindle is short It also is a2...
  16. If I have the right manual you connect P24 to 1...

    If I have the right manual you connect P24 to 1 for forward and P24 to 2 for reverse
    Both open is stop
    Almost any 1-0-2 switch can do that
    Its all in the manual
    Do not put a 3phase switch...
  17. Replies
    13
    Views
    1,088

    I make brackets that keep a gap between scales...

    I make brackets that keep a gap between scales and underside of the table to give space to a open end wrench to adjust the stops
    The scales I have are too wide to do it your way
    These stops are not...
  18. Problem solved But I still would like a diagram ...

    Problem solved But I still would like a diagram There was a left right switch added Or it has been replaced

    Peter
  19. Replies
    6
    Views
    591

    Now the power feed gearbox is mentioned It has...

    Now the power feed gearbox is mentioned It has some plastic selection levers I had one break once So ik you take it apart for some reason I would make a steel or bronze selectionlever

    Peter
  20. Replies
    6
    Views
    591

    Very good machines IMHO I did rebuild a couple ...

    Very good machines IMHO
    I did rebuild a couple
    But the Y stroke is not big enough I think to do the head on the ground in your last picture
    At least not with a cross hatch finish
    Make sure...
  21. Hardinge HLV-H with a KL2 circuit diagram

    I have heard from the Englisch KL1 version of the HLV-H
    But now I have a machine that says HLV-H on the name plate
    But there is a electrical diagram in there from Haysom engineering wich says KL2...
  22. Axa A link where you can download the prospect ...

    Axa
    A link where you can download the prospect
    Peter
    Brochures: AXA Maschinenbau
  23. Replies
    9
    Views
    999

    So not anything final about EM then I was...

    So not anything final about EM then
    I was thinking about €10500,- for the machine (11800USD)
    Cleaned and serviced
    That would be a fair price I think

    Peter
  24. Replies
    9
    Views
    999

    Picture is from the seller It is out by now ...

    Picture is from the seller
    It is out by now

    Peter
  25. Replies
    9
    Views
    999

    S/N HLV-H 693/2295 YOM is 1988 I read that...

    S/N HLV-H 693/2295
    YOM is 1988
    I read that the HLV-H EM just has HLV-H as a model No mentioning of EM
    So I wondered where the EM came from
    It probably stands for Englisch Metric
    But is...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4