Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: machineit2

Page 1 of 25 1 2 3 4

Search: Search took 0.01 seconds.

  1. Cut all power and check connections at the low...

    Cut all power and check connections at the low voltage power supply. Otherwise you are just going to check for loose wires and dirty connectors, again with all power off.
  2. Replies
    6
    Views
    5,206

    Nine year old post.

    Nine year old post.
  3. Replies
    37
    Views
    5,719

    I use Zaritron often, good people. I believe the...

    I use Zaritron often, good people. I believe the reloading of the software is only because it can't be retained during repair.
  4. Replies
    2
    Views
    504

    10 or 20% markup does not pay any company to buy...

    10 or 20% markup does not pay any company to buy those parts and put them on the shelf and in their trucks and service centers.

    When you make parts, just charge 10% over your actual costs of...
  5. Replies
    22
    Views
    1,979

    Glad it is fixed. :)

    Glad it is fixed. :)
  6. Replies
    20
    Views
    2,535

    I want to see you do my 14 and 19 inch shafts...

    I want to see you do my 14 and 19 inch shafts with that setup! LOL
  7. Harbor freight has 5 gal tanks for $30.00 and 11...

    Harbor freight has 5 gal tanks for $30.00 and 11 gal tanks for $40.00. I put a 5 gal one on each of my machines.

    You will also find you loose a lot of pressure from friction in running air in a...
  8. Almost all are single phase, and if it were a 3...

    Almost all are single phase, and if it were a 3 phase it would not run at all on only 2.
  9. Sounds like the motor is weak and when it starts...

    Sounds like the motor is weak and when it starts it thinks that the auger is jammed and reverses. That is what a good one would do.

    You might find it has gotten moisture inside and needs a good...
  10. Replies
    7
    Views
    680

    If your holes are all the same, then all you need...

    If your holes are all the same, then all you need after the first G83 call out is the next location. For example: X4.7235 Y-2.1875. When you call out the G83 again, it needs the Q and the R again....
  11. Replies
    20
    Views
    2,535

    Working at home. This is an old picture I had...

    Working at home. This is an old picture I had loaded for another post, so no aluminum to disregard-------Mike
  12. Replies
    20
    Views
    2,535

    You are making this a lot harder than it needs to...

    You are making this a lot harder than it needs to be. I have machined, tapped, single point threaded hundreds of parts up to 19" long. By using a 5c fixture on top of a face plate/angle block and...
  13. Replies
    114
    Views
    89,272

    It is a typical rookie mistake not to check the...

    It is a typical rookie mistake not to check the date of the thread, I think i did it early on too. :)

    Welcome to the forum Thx11382000 and keep on posting and reading. Enjoy the site.

    Mike
  14. Replies
    114
    Views
    89,272

    A nine year update, thanks. :)

    A nine year update, thanks. :)
  15. Replies
    23
    Views
    3,843

    Stoyan is great, I've used him several times and...

    Stoyan is great, I've used him several times and just bought a low voltage power supply last month.

    Mike
  16. Oh man, that does suck. Sounds like a visit from...

    Oh man, that does suck. Sounds like a visit from the Haas Tech.

    Sorry
  17. Dirt, It should work with that voltage. What...

    Dirt,

    It should work with that voltage. What is overhearing? Hook the two lower voltage lines to L1 and L3 and the higher one to L2. Connect taps to the lower voltage for the lower ones.

    Mike
  18. Sounds like you have yours miss-wired or the mill...

    Sounds like you have yours miss-wired or the mill has a problem. I have run off of PC's for nearly 20 years without issue. What are you voltages and how do have them wired to the mill?

    Mike
  19. Since you all were skeptical as to the quality,...

    Since you all were skeptical as to the quality, experience etc, I contacted John Cown again and asked how many of these boards they do. He was nice enough to reply:


    We repair about 3 a week on...
  20. Oh please, don't use any "LOGIC" in this thread,...

    Oh please, don't use any "LOGIC" in this thread, peoples heads may explode!
  21. How appropriate that this was posted to my...

    How appropriate that this was posted to my Facebook timeline today by a friend. Fits right in. You all fight it out on your own.
  22. Well, excuse me for putting words in your mouth...

    Well, excuse me for putting words in your mouth and for using my precious time to research and find a solution to a problem that I do not have and have never had. Excuse me for doing "your" fucking...
  23. No, his issue was cost and availability. Not...

    No, his issue was cost and availability. Not wanting to obsolete a machine because it was older.
  24. It is the testing procedure. Boy, hard to please...

    It is the testing procedure. Boy, hard to please some. Please feel free to get your up-grade directly from Haas.
  25. How much software is on the MOCON board? :) ...

    How much software is on the MOCON board? :)



    It's the processor board.
Results 1 to 25 of 614
Page 1 of 25 1 2 3 4