Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tony Quiring

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Sounds like a simple solution until you realize...

    Sounds like a simple solution until you realize there are gear interfaces between the 2 parts.

    Sent from my SM-G781V using Tapatalk
  2. That would be a very interesting court trial... ...

    That would be a very interesting court trial...

    Connecting lots of dots to who is responsible.

    Sent from my SM-G781V using Tapatalk
  3. Replies
    77
    Views
    4,733

    Seems like it is critical that the radius from...

    Seems like it is critical that the radius from center is critical so wheel is dead true to center.

    With the shape of the object or peg in one hole one should be able to fixture the part such one...
  4. It would seem the person who called FedEx would...

    It would seem the person who called FedEx would be fist in line.

    If you did not sign a document agreeing to be billed you should be fine.

    Seems like FedEx would not do a blind pickup, they...
  5. Replies
    28
    Views
    22,756

    Missing additional information. Duty cycle and...

    Missing additional information.

    Duty cycle and running time when needed.

    One determines how much time to charge battery and other determines how much battery you need.

    Sent from my SM-G781V...
  6. Thin wall tubing will require controll cut or...

    Thin wall tubing will require controll cut or fine teeth in the cutter.

    Slow speed will allow longer life.

    If using drill press use a fixture

    Simple enough to make from dimensional lumber....
  7. Replies
    643
    Views
    121,357

    Supply of rohn 25. Useful for something... ...

    Supply of rohn 25.

    Useful for something...

    Sent from my SM-G781V using Tapatalk
  8. Replies
    82
    Views
    16,528

    Agree... That is so true with most trades. ...

    Agree...

    That is so true with most trades.

    I am an old radio guy, got in when everything was component level and service van was equipped such you could do full repairs on site.

    It is not...
  9. Replies
    17
    Views
    1,081

    In simple terms... Imagine connecting a DC fan...

    In simple terms...

    Imagine connecting a DC fan motor to your car battery with a push button switch momentary contact type.

    Hold button on and motor runs full speed.

    Tap button for short...
  10. Forgot to mention the time... New stuff once...

    Forgot to mention the time...

    New stuff once you open the Gan will gell.

    Buy in container sized to the job.

    Any left over will turn to gell in not tooling of time.

    Sent from my SM-G781V...
  11. If you want it fast just use MEK. it will...

    If you want it fast just use MEK.

    it will instant bond.

    Most of the pvc glues currently may have some mek with other "safe" stuff.

    Purple primer is a must!

    The old stuff was mostly MEK...
  12. I repeat my suggestion using an extension cord...

    I repeat my suggestion using an extension cord plugged in near the panel to allow you to make measurements at different locations.

    Volts and continuity are easy with a VOM.

    This is not that...
  13. Yes but power off. Sent from my SM-G781V using...

    Yes but power off.

    Sent from my SM-G781V using Tapatalk
  14. Really? Have watched them do me 2 times,...

    Really?

    Have watched them do me 2 times, trucks and rocks ...

    They cut out old glass.

    Scrape off old stuff, did not look close enough to see how clean the body was but they did a test fit...
  15. Replies
    9
    Views
    826

    Fanless PC. Sealed box with no fans. Place...

    Fanless PC.

    Sealed box with no fans.

    Place inside a box then add a USB hub to have USB stuff plug in outside box.

    Sent from my SM-G781V using Tapatalk
  16. tomorrow? It is oversize then it is worn out...

    tomorrow? It is oversize then it is worn out scrap

    Sent from my SM-G781V using Tapatalk
  17. Lots of propane units available but much more...

    Lots of propane units available but much more complicated.

    Few low speed units and fuel system in cold area may require heating.

    Sent from my SM-G781V using Tapatalk
  18. A fox and hound works well for this. About a...

    A fox and hound works well for this.

    About a hundred bucks or so.

    The toner puts a tone on the wire and the wand has inductive pickup.

    Great for doing this and you will use it again.

    Sent...
  19. Look for 1800 rpm as the sound level will be...

    Look for 1800 rpm as the sound level will be greatly reduced.

    Diesel would be better as propane just costs too much for energy output.

    Have seen some that are connected to the utility provided...
  20. Moving the wires for testing is not wise. ...

    Moving the wires for testing is not wise.

    "TONY'S LAW" first rule is last guy did it wrong and that may be true.

    First since it was working then stopped is may have been close then something...
  21. Replies
    15
    Views
    1,227

    Yes. That is how Telcom switches have been...

    Yes.

    That is how Telcom switches have been done for many years

    Power plant is "float service" meaning it maintains the batteries at full charge while supplying power for the load.

    Is power...
  22. Replies
    15
    Views
    1,227

    You stated " BATTERY"... Look for good quality...

    You stated " BATTERY"...

    Look for good quality battery of AGM type that can run everything for a few minutes minimum.

    Meet get a battery charging power supply that will properly FLOAT the...
  23. Replies
    88
    Views
    7,119

    Close... The intent of my suggestion was to be...

    Close...

    The intent of my suggestion was to be able to repeat all motions in a different place.

    By cutting on the back side with carriage movement it is same extension of tooling and similar...
  24. Replies
    140
    Views
    16,661

    OCPH. Operational Cost Per Hour. Add all...

    OCPH.

    Operational Cost Per Hour.

    Add all costs of operating the company except input materials.

    Power, rent, payroll etc.

    Add up total available billable hours, not managers but just...
  25. Replies
    88
    Views
    7,119

    Get a chunk of round same length as your problem...

    Get a chunk of round same length as your problem then with lathe in reverse use suspect tools and cut on the back side of object.

    Same forces involved in slightly different spot.

    Sent from my...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4