Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 58 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    38
    Views
    2,193

    To hard... just fill with shop trash, chips,...

    To hard... just fill with shop trash, chips, rags, ect and pour over, that what the old timers did...Phil
  2. Replies
    1
    Views
    119

    Lots of luck I couldn't even find a winder, let...

    Lots of luck I couldn't even find a winder, let alone a CEO...Phil
  3. Replies
    28
    Views
    22,756

    Give it up and install a hand powered winch that...

    Give it up and install a hand powered winch that will work on all voltages, ha ha...Phil
  4. Replies
    10
    Views
    751

    Be careful on pricing, MAKE sure you cover the...

    Be careful on pricing, MAKE sure you cover the loading price, real easy to sell a machine to cheap and not cover the cost to load it, and the baby sitting is a pia...Phil
  5. Run from it... old as the hills and hard rubber...

    Run from it... old as the hills and hard rubber tires, only fit for flat floors, no outside stuff, and 6.5k insane... 1k is resell on that old junk...Phil
  6. Replies
    9
    Views
    575

    Ok I am a old fart...Phil

    Ok I am a old fart...Phil
  7. The very best deal of my life was buying two...

    The very best deal of my life was buying two 4x4x8 crates full of there left over tooling , I know where my tax dollars went...what a gold mine of 10ee parts and other goodies...Phil
  8. Replies
    9
    Views
    575

    You ask how? At the time I had a big hmb, no...

    You ask how? At the time I had a big hmb, no problem to do the machine-work on the Gorden, didn't even have to sweat...just picked the p2-3 up and bolted it to the hbm table and made chips.......
  9. Replies
    9
    Views
    575

    A real neat machine, I striped all the paragraph...

    A real neat machine, I striped all the paragraph parts and put a brigeport milling head on one...made a real nice milling machine...Phil
  10. Replies
    14
    Views
    641

    Save the oilier, gauges, and the pulleys...scrap...

    Save the oilier, gauges, and the pulleys...scrap the rest...Phil
  11. Replies
    40
    Views
    3,568

    Vanguard, I just got done with the worst 3 years...

    Vanguard, I just got done with the worst 3 years of my life selling of my shop. I had too, no auction house would take the job. In the end it would have been better to haul it all to the scrap...
  12. Old lathes dont have much value, most of the time...

    Old lathes dont have much value, most of the time a little more than the scrap value sri no gold mine...Phil
  13. Replies
    11
    Views
    900

    Hard to beat white lead, unless you eat it...Phil

    Hard to beat white lead, unless you eat it...Phil
  14. Replies
    13
    Views
    1,443

    I use 80/90 wt gear oil...Phil

    I use 80/90 wt gear oil...Phil
  15. Replies
    14
    Views
    932

    Jim 50/60 cps...Phil

    Jim 50/60 cps...Phil
  16. size on size , heat to install...Phil

    size on size , heat to install...Phil
  17. Replies
    14
    Views
    932

    looks like a single phase motor with a start cap...

    looks like a single phase motor with a start cap and a solid state start switch to me...Phil
  18. I will check with Hammer steel, over the years I...

    I will check with Hammer steel, over the years I bought a lot of tee rail from them...The rail in my train track is 40/60 lb rail used from a mine that shut down years ago...Phil
  19. I find it hard to believe 12 lb rail is $10/ft,...

    I find it hard to believe 12 lb rail is $10/ft, you need to do some shopping I think that about 2.50 a lb and rail is the cheapest iron one can buy...Phil
  20. If any of you have deep pockets I have a running...

    If any of you have deep pockets I have a running 36 gauge steam Locomotive with cars and track that could be had with enough zero,s...Phil
  21. Replies
    3
    Views
    494

    need all 3...Phil

    need all 3...Phil
  22. 300 lbs is child's play, move it whole...Phil

    300 lbs is child's play, move it whole...Phil
  23. Replies
    25
    Views
    2,081

    If you want to pay airfair bothways for me and my...

    If you want to pay airfair bothways for me and my gal I would be happy to show you...Phil
  24. Replies
    4
    Views
    610

    I had a tort, with a tube worked ok but I put a...

    I had a tort, with a tube worked ok but I put a 8x20 hood over the welding area, it worked better...had a 25 hp fan...Phil
  25. This is used on syc motors, will not work on...

    This is used on syc motors, will not work on induction motors...Phil
Results 1 to 25 of 1448
Page 1 of 58 1 2 3 4