Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: SBLatheman

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    9
    Views
    609

    Did you see post #5. ???

    Did you see post #5. ???
  2. Replies
    37
    Views
    2,527

    These machines have the Long bed, 4 1/2’, the...

    These machines have the Long bed, 4 1/2’, the longest bed offered. And at least one of them has a taper attachment.
    The prices will go up a lot before the auction ends:rolleyes5:
    Ted
  3. Replies
    9
    Views
    609

    This is a reverse bracket assembly for a 13” with...

    This is a reverse bracket assembly for a 13” with the small spindle only.
  4. Replies
    9
    Views
    609

    The “twin” gears are not twins in this case...

    The “twin” gears are not twins in this case :rolleyes5:
  5. Replies
    9
    Views
    500

    Nope:nono: not even close. Ted

    Nope:nono: not even close.
    Ted
  6. Replies
    8
    Views
    2,422

    send me an email. Ted [email protected]

    send me an email.
    Ted
    [email protected]
  7. Thread: SBL logo

    by SBLatheman
    Replies
    2
    Views
    434

    South Bend Lathe became “employee owned” July of...

    South Bend Lathe became “employee owned” July of 1975. The SBL logo came shortly after.
    Ted
  8. I have the tool post and a selection of push...

    I have the tool post and a selection of push button controls.
    Send me an email.
    Ted
    [email protected]
  9. I have a set of “digital dials” that were on a...

    I have a set of “digital dials” that were on a Bridgeport clone that a friend of mine had.
    Danatron brand. Backlash compensation wasn’t a big problem because it had ball screws.
    These are available...
  10. Replies
    25
    Views
    1,472

    When you are using the taper attachment, you...

    When you are using the taper attachment, you remove the screw that holds the CF nut to the cross slide. That knurled part is used to fill the hole in the cross slide(if it is original)and you store...
  11. Replies
    6
    Views
    688

    IF this index plate is original, then the machine...

    IF this index plate is original, then the machine was made in 1975 or later.
    According to Steve Wells, the “O” means that it has a D1-4 spindle. I have seen others that had the “O” that did not have...
  12. Replies
    23
    Views
    1,523

    Bill, The compound in the picture is not a...

    Bill,
    The compound in the picture is not a South Bend. This one has two screws to attach it to the cross slide and just a pin in the center for the pivot, I don’t know the brand. The cross slide is...
  13. Replies
    23
    Views
    1,523

    I have the one in the picture...2 3/4” travel...

    I have the one in the picture...2 3/4” travel
    $90 plus $15 shipping
    Ted
    [email protected]
  14. Replies
    23
    Views
    1,523

    How much travel do you need ?

    How much travel do you need ?
  15. Replies
    5
    Views
    1,116

    I have a manual. Send me an email Ted...

    I have a manual.
    Send me an email
    Ted
    [email protected]
  16. Replies
    25
    Views
    2,088

    I installed the motor and all the wiring on the...

    I installed the motor and all the wiring on the machine today. Smooth and quiet :)
    ...but, as luck would have it, forward/reverse is backwards :rolleyes5:
    I assume I need to switch the red and...
  17. Replies
    25
    Views
    2,088

    Eureka ! ! That worked :o Thank you very much,...

    Eureka ! ! That worked :o
    Thank you very much, Allan, you certainly know what you are talking about :)
    Thanks again,
    Ted
  18. Replies
    25
    Views
    2,088

    More info: The brown goes to the centrifugal ...

    More info:
    The brown goes to the centrifugal switch
    The black wire goes to the capacitor
    Red goes into the windings, and so do the yellow ones.

    Thanks for everybody’s help :)
    Ted
  19. Replies
    25
    Views
    2,088

    I had time this morning to wire it up.(on the...

    I had time this morning to wire it up.(on the bench)
    Flipped the switch on direction and the motor started right up, a little rough running. Shut it off and flipped it the other direction. It...
  20. Replies
    8
    Views
    956

    It is a D1-8...that was the only spindle nose...

    It is a D1-8...that was the only spindle nose offered.
  21. Replies
    25
    Views
    2,088

    Thank you, Allan. That is a very elegant...

    Thank you, Allan. That is a very elegant solution...if it works:)
    I will test the capacitor like you suggested first and let you know how it worked out.
    Regards,
    Ted
  22. Replies
    12
    Views
    765

    I thought that machine looked too big to be a 13”...

    I thought that machine looked too big to be a 13” :skep:
    It is a 16”, as shown by the index plate
    Ted
  23. Replies
    25
    Views
    2,088

    They are pretty good pictures, but they don’t...

    They are pretty good pictures, but they don’t post very well:confused:
    I can email them to you.
    Ted
    [email protected]
  24. Replies
    25
    Views
    2,088

    Wiring motor/switch help...Please

    Wiring motor/ switch help...Please

    This motor is on a Heavy 10 that I bought. The previous owner had replaced the 3-phase motor with this Dayton, wired to just run forward(220v 1-phase). I want it...
  25. Replies
    5
    Views
    1,116

    The CS33 was made in Spain by METOSA. South Bend...

    The CS33 was made in Spain by METOSA. South Bend imported them for a few years, then Clausing picked them up. You should be able to get parts from them.
    (I still have a few parts)
    Ted
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4