Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: JohnEvans

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Gee ,Looks more like a planer to me !!

    Gee ,Looks more like a planer to me !!
  2. The zerks one the end of the table on the BP...

    The zerks one the end of the table on the BP looks like grease on them. Big NO NO !!
  3. There is no such thing as a repair manual for any...

    There is no such thing as a repair manual for any Grizzly product . Grizzly bought the South Bend NAME only that is the ONLY relationship there. The only "timing" involved is when you engage the half...
  4. Replies
    2
    Views
    276

    Try this on for size !! And no comments about my...

    Try this on for size !! And no comments about my shaky writing ! LOL
  5. Replies
    14
    Views
    5,044

    good luck with that ,OP has not been on the forum...

    good luck with that ,OP has not been on the forum in about 2-1/2 years.
  6. Well the portable boring bar unless it has ALL of...

    Well the portable boring bar unless it has ALL of it's tooling is worth very little ,they do make a good floor lamp bases however.
    As said to rebuild modern engines it takes much more...
  7. Good luck with that price,Be suprized if you even...

    Good luck with that price,Be suprized if you even get a bid.
  8. Replies
    11
    Views
    1,827

    Yep! your area for that machine I would guess...

    Yep! your area for that machine I would guess $500 would be more realistic. Real short bed no quick change minimal tooling. Here in Phoenix I might be able to get $650-700 for it.
  9. Replies
    11
    Views
    1,827

    Logan spec sheet says 25/32 spindle bore for...

    Logan spec sheet says 25/32 spindle bore for model 1400.
  10. [QUOTE=snypr;3776015]If possible, I would really...

    [QUOTE=snypr;3776015]If possible, I would really like a copy of the manual as well. email address is [email protected] (my attempt @ misleading email harvesting bots). Thank you in advance.[/QUOT...
  11. See what Amazon has . I have bought several 6" 3...

    See what Amazon has . I have bought several 6" 3 jaw flat back for just over $100 free shipping. Was more than pleased with the quality. CME tools usually have good prices on back plates and...
  12. Try getting some cleaner/lube on top of the pin...

    Try getting some cleaner/lube on top of the pin in pic 1 ,that was the area that I found was the most likely to be stuck from oxidized old oil. Mills that had been in regular use until we got them...
  13. Here are some pictures. If you pull the rule off...

    Here are some pictures. If you pull the rule off you can see the top of the pin in the block when feed is disengaged. see pic 1 scribe is pointing at it.
    Also most BP you can't engage the until the...
  14. Part #100 is what usually gets gummed up. Pull...

    Part #100 is what usually gets gummed up. Pull the link on the bottom of the casting that the feed stop rod operates to push up #100 then you can pull #100 down and out to de-gum. Part #94 if you...
  15. The usual cause is the pin inside the sliding...

    The usual cause is the pin inside the sliding block the lever shifts to the right is gummed up with old oil. Does not drop down to engage. a 50-50 mix of ATF and acetone applied liberally will free...
  16. FS KD piloted adjstable reamers SPI parallels miics & misc

    OK I'm getting lazy ,here is a link to my local Clist sale. Some of it shipping cost in more than the item is worth.
    Machinist Tools and Tooling - tools - by owner - sale

    You see something that...
  17. Weld or press fit with a key . Press with a key...

    Weld or press fit with a key . Press with a key would be the way I would do it with that material.
  18. Replies
    16
    Views
    9,561

    Well !! His profile shows he was last on the...

    Well !! His profile shows he was last on the forum a year ago!! I'd say not much chance. His profile shows you can send him a email,might try that.
  19. Offers ?

    Reasonable offers will be considered and a bump while I am at it !:)
  20. PM inbound Thanks

    PM inbound Thanks
  21. FS Wavy parallel- gear gauge-B&S-Wahlstrom chuck- mag chuck

    More box clean out stuff
    A. SPI Swiss made wavy parallel set 1/2 -1-1/2 $110
    B. B&S 1-2" inside mic $45
    C.SOLD Boston gear gauge 14.5 & 20* set $45
    D....
  22. Replies
    8
    Views
    562

    Well my mill is a V/S so can't pull it out to...

    Well my mill is a V/S so can't pull it out to look. And it has been 3-4 years since I worked one that area. If course thread looking my next idea would be 5/16-18.
  23. Replies
    8
    Views
    562

    Try a 1/4-20 bolt !! You want your hand held too...

    Try a 1/4-20 bolt !! You want your hand held too ! LOL You kids .
  24. the best thing to do with the HF lathe shaped...

    the best thing to do with the HF lathe shaped object is dump in the recycle barrel . junk for any real work.
  25. I looked at that link to get a idea of prices....

    I looked at that link to get a idea of prices. Holy moley !!! If I had to replace what I have with new I bet I would have a $7-8000 bill!! About 18-20 collet and side lock holders ,full set of the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4