Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: maynah

Page 1 of 60 1 2 3 4

Search: Search took 0.02 seconds.

  1. Replies
    43
    Views
    1,483

    I never had the cabinet. A guy was parting it out...

    I never had the cabinet. A guy was parting it out along with some other lathe parts. He had given the cabinet and the motor to his buddy. I wanted the 3 jaw chuck with threadlock mount and the...
  2. Replies
    43
    Views
    1,483

    Reggie, I'm going to part my lathe out at some...

    Reggie, I'm going to part my lathe out at some point so if you do destroy anything I probably have what you need.
  3. Replies
    43
    Views
    1,483

    Here are a few of pictures of my Wade 73. You...

    Here are a few of pictures of my Wade 73.
    You say it's a 5C collet. Could it be the drawbar is 8W collet threads?
    I think the only difference is the Wade uses buttress threads.

    ( I usually...
  4. Replies
    139
    Views
    78,739

    This Wagner motor is on an old compressor. Not...

    This Wagner motor is on an old compressor. Not factory, it's cobbled together.
    The brush set-up is interesting because it's radial not axial if that's the right term.
    I'm not sure it ever had a...
  5. Replies
    34
    Views
    6,909

    Of course you're right OM. My brain is slowly...

    Of course you're right OM.
    My brain is slowly turning to mush.
    And I should know better, I have an Oliver 55 wood lathe.
  6. Replies
    34
    Views
    6,909

    There's one on Maine CL right now. Looks like...

    There's one on Maine CL right now.
    Looks like it's been used as a pencil sharpener.
    $675

    324528324529
  7. Replies
    12
    Views
    1,080

    Welcome 1965. If you post this over in the...

    Welcome 1965.
    If you post this over in the "Deckel, Maho, Aciera, Abene Mills" forum I bet someone there will know.
    The worst that can happen is Milacron won't like it there and move it back here.
  8. Replies
    26
    Views
    1,997

    Kinda looks like its been in a fire to me....

    Kinda looks like its been in a fire to me.
    Still, very interesting.
  9. Replies
    4
    Views
    574

    I don't know but it's a nice one. A lot more...

    I don't know but it's a nice one. A lot more going on than your garden variety Barnes, Seneca Falls, Young, etc.
  10. When I had put 50 photos in my album it wouldn't...

    When I had put 50 photos in my album it wouldn't let me post any more full size pictures.
    So I deleted one like John did and it did remove the photo from my album and old post.
    Is there a way to...
  11. Replies
    17
    Views
    1,351

    I don't own it, I just post things like this for...

    I don't own it, I just post things like this for future searchers.
    And Rob identified it. Someone is really going to appreciate that some day.
    Vintage Machinery is pretty good for an archive, but...
  12. Replies
    17
    Views
    1,351

    Thanks for that info Rob, interesting.

    Thanks for that info Rob, interesting.
  13. Replies
    17
    Views
    1,351

    Cute little T&C grinder

    This is on Worchester Mass CL.
    I'm guessing Fairbanks is the seller, not the maker.
    Interesting to me that Bangor Me. is listed with all those other bigger cities.
  14. Replies
    24
    Views
    1,690

    First thing is check the back side of the plate....

    First thing is check the back side of the plate. Many are through drilled and if you can get a small punch behind it you can just tap them out. (I'm writing this for the guys who haven't done many,...
  15. Replies
    22
    Views
    2,087

    Thanks for the input. Another negative would be...

    Thanks for the input.
    Another negative would be how fast it would bottom out backing up a slight grade.
    I think I'll pass on it.
  16. Replies
    22
    Views
    2,087

    We'll assume no suspension. I don't know enough...

    We'll assume no suspension.
    I don't know enough about trailers to know if that's common.
    I can just envision hauling the empty trailer on a Maine road during mud season when the pot holes appear...
  17. Replies
    22
    Views
    2,087

    That beam looks red in this picture. It may just...

    That beam looks red in this picture.
    It may just be the trailer frame.
  18. Replies
    22
    Views
    2,087

    No springs on a trailer?

    I'm looking at trailer with no springs on the axles. At first thought, I don't like the idea. Seems like it would bounce quite a bit if you hit a sizable pot hole. But I do like how low it sits. I...
  19. Replies
    3
    Views
    348

    I have the same lathe. OC gearbox, conehead. I...

    I have the same lathe. OC gearbox, conehead.
    I think mine's around 1918.
  20. Joe, I was going to send you the link in a PM but...

    Joe, I was going to send you the link in a PM but your inbox is full.
    Hiram is not that far from you.
  21. Barnes lathe drive on Maine fb market place

    Looks complete with flywheel, sprocket, 2 sets of legs, pedal assembly and a few small bits.
    $500 maybe a bit high but try to find them somewhere. (keep the best legs sell the others)
    They're...
  22. Replies
    4
    Views
    659

    I think you have the right tap. Are you sure the...

    I think you have the right tap. Are you sure the tube is a thin wall tube?
  23. Replies
    21
    Views
    1,460

    I used to work for a moving company in a earlier...

    I used to work for a moving company in a earlier life that was just across the Capital Beltway from Andrews Air Force Base. We had a lot of part time Air Force help. It didn't take long for the boss...
  24. Here is a 5V collet. That's a 4" scale.

    Here is a 5V collet.
    That's a 4" scale.
  25. I have a little Van Norman bench lathe with the...

    I have a little Van Norman bench lathe with the key at the front of the spindle.
Results 1 to 25 of 1497
Page 1 of 60 1 2 3 4