Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: HS70A Brother

Search: Search took 0.00 seconds.

  1. Replies
    4
    Views
    1,659

    Found this on Ogura's web site ...

    Found this on Ogura's web site

    https://ogura-clutch.com/files/pdf/OPBN_Data.pdf

    The -10 looks like ours but does not have the second shaft for our tech and the one shaft is larger too.

    I...
  2. To many what's missing,where is it and what's...

    To many what's missing,where is it and what's that.
    Its out of service for a good and expensive reason.
    The missing lower wire chopper....$7000.00 Any bad boards $10,000.00+.
    That been my...
  3. Maybe there isn't any floor space for the water...

    Maybe there isn't any floor space for the water chiller?
  4. Replies
    2
    Views
    1,163

    Happy days. :) Thanks to J&J at GTD We have...

    Happy days. :) Thanks to J&J at GTD We have acquired three more used Brother HS70 wire EDM machines. Two HS70As and one nice HS70-AM.
    A little TLC and they will be cutting parts again.

    Question,...
  5. Replies
    4
    Views
    1,659

    Steve, Been there, done that. Ogura Model...

    Steve,
    Been there, done that.
    Ogura Model #OPB-10N-07 DC-24v with S/N
    The manufacture recognizes this number as a PROPRIETORY number and will not sale retail.:icon_bs:

    I've been successful...
  6. Replies
    3
    Views
    1,308

    Sorry to hear your machine is down. I guess this...

    Sorry to hear your machine is down.
    I guess this isn't the first time your machine has been down.
    Ten,twelve years ago I acquired a defective front wire transport panel for a HS-70A.
    It had a...
  7. Most CNCs can save points independent of the part...

    Most CNCs can save points independent of the part program, P1,P2, ect.
    Then you can move to these points independent of the part program.
    Reference your manual to learn how for your machine type....
  8. Replies
    2
    Views
    1,163

    271222 Please don' let this happen to your...

    271222
    Please don' let this happen to your Brother HS-70A-M wire EDM. Call ME!
    Regards,
    John

    Phone 714 785 zero4two3
  9. Replies
    2
    Views
    1,163

    WTB Brother HS70A or HS70A-M Wire EDM

    WTB Brother HS70A or HS70A-M Wire EDM.
    Will consider running or not.
    Also WTB some parts from the older Brother machines.
    Let me know what you have.

    Regards,
    John
    714-785 zero4two3 Please...
  10. I have lots of Brother power pins but I have an...

    I have lots of Brother power pins but I have an easy way to assure lower power pin cooling without disassembly of the lower head.
    Simply remove the lower wire guide from the head assembly and drill...
  11. I'd do a visual check with a good magnifier of...

    I'd do a visual check with a good magnifier of the solder joints on the boards. You are looking for any cracks indicating a "cold" solder joint.
    The next thing to do is swap the DC PCB board with...
  12. error 8108&8109: An error occurred in the u-v...

    error 8108&8109:
    An error occurred in the u-v axis servo driver or motor. The axis may have contacted an obstacle. Cable connection maybe faulty or cable maybe damaged.

    With so few hours, my...
  13. Replies
    6
    Views
    2,900

    I'm not much of a tec writer but here goes. Bad...

    I'm not much of a tec writer but here goes. Bad news is the backup battery died and you have lost the data needed to "home" the machine..ect. There is other data lost, lead screw comp., power...
  14. Wtb only the "BROTHER HS70A-M" wire edm machines

    Hello everyone. As you may or may not know GF will no longer support the Brother line of wire EDM machines after this year 2018. I have been a loyal Brother wire EDM user for 30 years. Machines I...
  15. Have had the same problem but in the +Y...

    Have had the same problem but in the +Y direction, when very close to the +y limit.
    A carful deep cleaning of the groves in the lower arm bellows helped.

    Regards,
    John
  16. Replies
    3
    Views
    1,898

    Can you flip the part over and burn from the...

    Can you flip the part over and burn from the other side?
    Works for me.

    Regards,
    John
  17. Replies
    31
    Views
    6,730

    My Brother COMs communication software worked...

    My Brother COMs communication software worked well with Microsoft ME software.
    Supported HS300, HS3100 and HS5100 machines.
    The machines wanted to be on the "machine" page.
    After starting the COMS...
  18. If you have a preferred EDM in mind. Ask the...

    If you have a preferred EDM in mind. Ask the dealer for a test cut in your material.
    The will be happy to develop a turnkey system for your needs.

    Regards,
    John
  19. Replies
    4
    Views
    1,599

    I have used stand alone Ebbco units with my wire...

    I have used stand alone Ebbco units with my wire edm machines for many years.
    But we now are so space limited the Ebbco unit have been put in storage off suit.
    I would recommend the 10 micron...
  20. Replies
    3
    Views
    1,942

    A or B, wire wins every time. Regards, John

    A or B, wire wins every time.

    Regards,
    John
  21. Replies
    7
    Views
    3,623

    The tricky one is a worn lower contact. The...

    The tricky one is a worn lower contact. The controller "checks for spark quality feedback" there.
  22. The smell could be from the D.I. level being to...

    The smell could be from the D.I. level being to high.
    The "suds" could be from a low water level allowing air to be sucked into the pump.
    Hope this helps.

    Regards,
    John
Results 1 to 22 of 22