Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Go to fleebay and find a fincor or AB drive, and...

    Go to fleebay and find a fincor or AB drive, and look at any info you have and see if the old drive had field weaking, there's a lot to know...Phil
  2. Replies
    6
    Views
    366

    I called them Fly press,s, crank the wheel until...

    I called them Fly press,s, crank the wheel until it is going real good and let it fly into the work...Phil
  3. Replies
    14
    Views
    449

    Use the vfd...Phil

    Use the vfd...Phil
  4. Replies
    9
    Views
    382

    Class "0" timkins are going to be outrageous in...

    Class "0" timkins are going to be outrageous in cost, and nothing else will do, show bigger, better pics of races, maybe there not that bad...Phil
  5. Replies
    9
    Views
    712

    Just a tilting roto table, looks pre ww2 with...

    Just a tilting roto table, looks pre ww2 with mounting feet...Phil
  6. Fuse,s would be better...phil

    Fuse,s would be better...phil
  7. Whats the hp of the single phase motor and the...

    Whats the hp of the single phase motor and the rating of the contractor?...Phil
  8. Replies
    28
    Views
    1,404

    Maybe you need a few more lawyers down there...we...

    Maybe you need a few more lawyers down there...we have a few extra we could send you if you want...Phil
  9. Replies
    19
    Views
    925

    Easy to snap off...Phil

    Easy to snap off...Phil
  10. Replies
    26
    Views
    711

    Good chance you will kill the starting caps with...

    Good chance you will kill the starting caps with low voltage, and might overheat the winding's. The starting amps on a 10hp will be over 200amps for 3 sec or so...#6 is good for 60 amps. I would use...
  11. Replies
    28
    Views
    1,404

    You are missing the point, the cust. spec was a...

    You are missing the point, the cust. spec was a 4hr time, you on your own used a 8hr cook time, It don't mater if it was harmless, you didn't do what the cust asked for...Now you can tell him and...
  12. Replies
    3
    Views
    384

    Apples and oranges, Try one and twink to...

    Apples and oranges, Try one and twink to fit...Phil
  13. Replies
    2
    Views
    263

    Just a guess, a pix would help... A rest to face...

    Just a guess, a pix would help... A rest to face bowls maybe...done by a fool...what does the rest of his machines look like?...Phil
  14. Replies
    28
    Views
    1,404

    Save face, scrap the bar, buy new and do it...

    Save face, scrap the bar, buy new and do it right, never tell the cust you are a twit and you cant do the job right....Phil
  15. Replies
    12
    Views
    516

    No value, hard tires,old old old, $500.00 would...

    No value, hard tires,old old old, $500.00 would be to much...Phil
  16. Not a good idea for a manual machine, fit new...

    Not a good idea for a manual machine, fit new acme,s and go on...Phil
  17. Replies
    11
    Views
    461

    Made 1941 soft ways,not very valuable... 1k...Phil

    Made 1941 soft ways,not very valuable... 1k...Phil
  18. Ya, the old I don't want to do it the hard way,...

    Ya, the old I don't want to do it the hard way, Use elbow grease and scrap. sand and polish the rust away.....only way its going to happen....Phil
  19. PAY A MACHINIST TO BUILD IT FOR YOU THAT does...

    PAY A MACHINIST TO BUILD IT FOR YOU THAT does HAVE A LATHE, JUST A THOUGHT....Phil
  20. Replies
    26
    Views
    2,111

    In the week this thread has been going on I could...

    In the week this thread has been going on I could have made a few steady rests....Hi Hi...Phil
  21. Looks like drum cutter for removing the end of a...

    Looks like drum cutter for removing the end of a oil drum...Phil
  22. Keep in mind what goes in has to (someday) come...

    Keep in mind what goes in has to (someday) come out, and it might be your wife or son in law in charge doing the job... I would add a new header and a taller door...Phil
  23. Replies
    133
    Views
    6,514

    Keep in mind you have to go where the work...

    Keep in mind you have to go where the work is....Phil
  24. You will need to start and keep the hole going...

    You will need to start and keep the hole going straight, I use a end mill for the first 1/2 inch or so to make a good straight hole, then short bits until I have to use the long one.Drill the hole...
  25. Replies
    133
    Views
    6,514

    Montana has no tax on the machine tools under...

    Montana has no tax on the machine tools under 100k, but taxes on land and building are a joke, my shop... 6000sqr ft w/crane went form $2800 4 years ago to $12000 now....Have to quit... no way to pay...
Results 1 to 25 of 289
Page 1 of 12 1 2 3 4