Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Limy Sami

Page 1 of 60 1 2 3 4

Search: Search took 0.11 seconds.

  1. Replies
    10
    Views
    394

    Please bear in mind this is what I was taught 50...

    Please bear in mind this is what I was taught 50 years ago (so may be out of date).............oh, and on another continent to boot ;)

    1, Did you flux the joint before preheating?

    2, was the...
  2. Replies
    3
    Views
    255

    Twas my pleasure Pete :)

    Twas my pleasure Pete :)
  3. Replies
    3
    Views
    255

    Try looking up 1/4 BSP

    Try looking up 1/4 BSP
  4. Replies
    21
    Views
    802

    If your customer won't change, change your...

    If your customer won't change, change your customer.
  5. FWIW in the UK, ''GUN TAP'' is an old name for a...

    FWIW in the UK, ''GUN TAP'' is an old name for a machine tap for through holes (aka Spiral Point)
  6. Replies
    12
    Views
    569

    That is something I would not want to even think ...

    That is something I would not want to even think about :eek:


    :D
  7. Why do you think / assume I was referring to you?

    Why do you think / assume I was referring to you?
  8. Looks like a bullshit button's got stuck again.

    Looks like a bullshit button's got stuck again.
  9. Replies
    97
    Views
    29,917

    Yup DS = double slide, as in under the hex turret...

    Yup DS = double slide, as in under the hex turret (in Peter S's pic 3)

    Warning / tip / hinte / whatever. .........regularly remove and clean that short slide block, and replace the wipers -...
  10. No, Gardner 8LXB

    No, Gardner 8LXB
  11. Replies
    29
    Views
    1,550

    Re grade of finish, .............with all the...

    Re grade of finish, .............with all the talk of cuts / inch etc etc, bear in mind the finish is only applied on the final cut, so tool wear shouldn't be a problem, ......and as it's only 1 cut...
  12. I freely admit to not knowing anything about...

    I freely admit to not knowing anything about Robodrills (or any other CNC whatever) .but to me that sounds like ''over meshing gears''
  13. Thank you Jim, .......I've ''suffered'' the same...

    Thank you Jim, .......I've ''suffered'' the same thing for eons .....................while not knowing such a phenomina exists.

    A bit of a handful? ........and then some :eek: ...
  14. Replies
    21
    Views
    802

    Sounds to me like a steady can only help, ..make...

    Sounds to me like a steady can only help, ..make up a catspaw sleeve (with 2 screws per flat) and set that true on the SQ bar for the steady to run on.

    BOTOH what you describe sounds a lot like...
  15. Replies
    6
    Views
    1,406

    I have several extra extra long 3/16 (I think?? )...

    I have several extra extra long 3/16 (I think?? ) MT1 drills where a straight shanked drill was brazed in to a MT shank - at the factory (Dormer IIRC) and very nicely done too, ............I expect...
  16. Buy a Prius.

    Buy a Prius.
  17. Replies
    7
    Views
    689

    I think (that's ?????????????? cus I'm not...

    I think (that's ?????????????? cus I'm not mathematicin) we need to know the pitch dia of the pinion gear that rides on the rack - so we can work out the leverage etc etc, ..................along...
  18. Replies
    27
    Views
    918

    F'k off spamtwat

    F'k off spamtwat
  19. Replies
    4
    Views
    861

    That'll cure your constipation.

    That'll cure your constipation.
  20. I smell a rat here guys, ..................like a...

    I smell a rat here guys, ..................like a trepanning shop that doesn't have ready buyers or know where to ''offload '' the cores ?????

    Nah - not buying it.
  21. Thread: best Motor

    by Limy Sami
    Replies
    10
    Views
    456

    F'k off spamtwat.

    F'k off spamtwat.
  22. Replies
    14
    Views
    443

    Something or nothing (and I know it's on the...

    Something or nothing (and I know it's on the other side of the world ;) ) but if you haven't already, check out these folk - they may ??????have a better price for your parts.

    Buy LG Washing...
  23. Replies
    23
    Views
    1,978

    YES We may have once been zero $ newbies, but we...

    YES We may have once been zero $ newbies, but we remembered our manners and even if we weren't buyin, managed find a way of thanking someone who'd helped us
  24. Replies
    23
    Views
    1,978

    Such are the days in which we live Bob :(

    Such are the days in which we live Bob :(
  25. Yup, if it's a goodun I'd go for it, ....as for...

    Yup, if it's a goodun I'd go for it, ....as for price I haven't a clue, and personally speaking I usually work on what it's worth to ME.
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4