Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Peter from Holland

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Dual speed motor perhaps?? Instead of dual...

    Dual speed motor perhaps?? Instead of dual voltage ??

    Peter
  2. I agree If is is a special motor (wierd...

    I agree
    If is is a special motor (wierd flangemotor for example)I would investigate if it could be rewound for 240volts

    Peter
  3. Reverse IP shows 3 websites of which 2 are in...

    Reverse IP shows 3 websites of which 2 are in Lagos Nigeria
    Scam for sure
    As I told them in my last e-mail that machines do not leave my warehouse before it is payed for in full in irreversable...
  4. The google streetview is from 2019 And I do not...

    The google streetview is from 2019 And I do not see that address listed at the Rexnord website any more

    Peter
  5. Information about a compagnie needed

    Anyone know this company
    Addax Industrial Machinery Inc.
    4701 Greenfield Ave,
    Milwaukee, 53214
    Wisconsin,
    ADDAX INDUSTRIAL MACHINERY INC | Home


    Bill is the one I had a...
  6. Replies
    20
    Views
    1,254

    I double your money :D For spares you could...

    I double your money :D

    For spares you could also ask Ruemema
    Drehmaschinen von Ruemema
    He is one of 2 I am aware of that is capable of rebuilding a 135 to original or better specs Also a very...
  7. On many machines ,Schaublin and Weiler to mention...

    On many machines ,Schaublin and Weiler to mention 2 ,a clamp can be used to keep the chuck on when turning in revers
    Attached a picture of one
    339780
    The sleeves in the flangebody you do not...
  8. Replies
    29
    Views
    1,620

    That pallet is too flimsy to be helpfull I...

    That pallet is too flimsy to be helpfull
    I prefere decent straps over bolts
    Drilling machine is always a bitch to transport
    Horizontal you need a special big enough pallet and blocks to keep...
  9. Yes .......................... Peter

    Yes ..........................

    Peter
  10. Remove the key and rotate the quill perhaps ?? ...

    Remove the key and rotate the quill perhaps ??

    Peter
  11. We put the 2 heaters in serie and tested again...

    We put the 2 heaters in serie and tested again After a much longer time as before it tripped once more
    So it did have some effect at least
    But.....
    After further inspection we discovered that it...
  12. Replies
    20
    Views
    1,254

    Buy buy buy buy

    Buy buy buy buy
  13. The thermal overload is in the 220volts 50 hz...

    The thermal overload is in the 220volts 50 hz supply line So that is where I measure
    Peter
  14. I measured less as 2 amps with a clamp on amp...

    I measured less as 2 amps with a clamp on amp meter Running at different speeds or starting had little to no influence
    Peter
  15. Replies
    20
    Views
    1,254

    It all depends on the price If it is GBP2500 or...

    It all depends on the price
    If it is GBP2500 or less

    BUY BUY BUY

    If under GBP 5000
    If it runs decent and all works sort of
    Buy

    Over GBP 5000
  16. I optioned that already :D Thanks Peter

    I optioned that already :D



    Thanks
    Peter
  17. That is why these are made from 16% Crome steel ...

    That is why these are made from 16% Crome steel
    And even then

    Peter
  18. Replies
    4
    Views
    329

    And you can buy new charts from Schinfa Peter

    And you can buy new charts from Schinfa


    Peter
  19. Contactor Overload Relays on 2 phases

    I have a contactor overload relay Telemecanique LR2 D13 1.6 to 2.5 Amp
    It is protecting a 220 V 2Ph circuit board to drive a DC motor
    We measure a load of 1.8 amps with a clamp on At least clearly...
  20. That 2 coloured wire (green/yellow) is ground ...

    That 2 coloured wire (green/yellow) is ground Theother ones are the 3 hot wires

    Peter
  21. Replies
    6
    Views
    604

    On most milling ma hines you have a long r...

    On most milling ma hines you have a long r spindle and a short nut On this one you have half a nut that is long but with a big diameter 60 - 70mm from memory The spindle is short It also is a2...
  22. If I have the right manual you connect P24 to 1...

    If I have the right manual you connect P24 to 1 for forward and P24 to 2 for reverse
    Both open is stop
    Almost any 1-0-2 switch can do that
    Its all in the manual
    Do not put a 3phase switch...
  23. Replies
    13
    Views
    1,091

    I make brackets that keep a gap between scales...

    I make brackets that keep a gap between scales and underside of the table to give space to a open end wrench to adjust the stops
    The scales I have are too wide to do it your way
    These stops are not...
  24. Problem solved But I still would like a diagram ...

    Problem solved But I still would like a diagram There was a left right switch added Or it has been replaced

    Peter
  25. Replies
    6
    Views
    604

    Now the power feed gearbox is mentioned It has...

    Now the power feed gearbox is mentioned It has some plastic selection levers I had one break once So ik you take it apart for some reason I would make a steel or bronze selectionlever

    Peter
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4