Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: boomerang69

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    0
    Views
    623

    FS Bridgeport series 1 cnc mill

    I have for sale a bridgeport mill R2E4 cnc mill.I purchased this years back with plans of retrofitting a centroid control but its not gonna happen.It was originally owned by John Tyler Community...
  2. Replies
    11
    Views
    817

    I had a 20 cm years ago that would swing 30.5,the...

    I had a 20 cm years ago that would swing 30.5,the original paper work from monarch called it raised in the sand.
  3. Thats my luck

    Thats my luck
  4. it gives full table traverse in very little...

    it gives full table traverse in very little effort,its one of the reasons I bought it.
  5. You'd have to pack 2 coolers for that trip

    You'd have to pack 2 coolers for that trip
  6. FS Brown and sharpe 510 surface grinder

    Running out of room in the shop,time to thin the herd.Brown and sharpe 5"by 10" manual surface grinder with Yuasa fine pole chuck.Roller bearing table,dust collector,has some backlash in y axis.220 3...
  7. Replies
    6
    Views
    556

    look up mcmaster carr # 6343k16,I had a part that...

    look up mcmaster carr # 6343k16,I had a part that used those to hold a 25mm bearing
  8. Replies
    6
    Views
    556

    I think what you have there is a bearing locknut

    I think what you have there is a bearing locknut
  9. sending a pm

    sending a pm
  10. sending you a PM

    sending you a PM
  11. Replies
    10
    Views
    782

    I have plenty of 3"square crs, I'm not too far...

    I have plenty of 3"square crs, I'm not too far from mebane, I'm in halifax if you want to pick it up.
  12. 17ft.should be dead on, my 24 by 174 is 21 ft.One...

    17ft.should be dead on, my 24 by 174 is 21 ft.One helluva nice lathe,you will love it.
  13. Replies
    57
    Views
    5,193

    The kitchen equipment was purchased by a guy who...

    The kitchen equipment was purchased by a guy who sells, refurbishes that stuff.The kondia mill sold for 1200.00 .Their were 4 standard modern lathes ,one with dro sold for 3500.00, two sold for...
  14. Replies
    57
    Views
    5,193

    Halifax County,The kitchen equipment like huge...

    Halifax County,The kitchen equipment like huge mixers were strapped to pallets and all the parts that went with them was on pallets shrink wrapped.the damn machine tools were spread out all over the...
  15. Replies
    57
    Views
    5,193

    local school auction turns to crap

    been a while since I posted but have been enjoying everyones post.I wanted to ask if anyone has been to your local school system surplus auctions to find most of the stuff comepletely destroyed.This...
  16. Replies
    15
    Views
    2,338

    Looks like a boring bar wrench

    Looks like a boring bar wrench
  17. Replies
    11
    Views
    2,146

    Thanks for your reply guncrank,in the picture of...

    Thanks for your reply guncrank,in the picture of the leadscrew I thought it looked like a repair where the shear pin is.I see on some of the others I looked at it looks the same.This came from the...
  18. Replies
    11
    Views
    2,146

    thanks for the replies,I checked out some youtube...

    thanks for the replies,I checked out some youtube videos and all that showed them running,the leadscrew was turning.Its not that big of a deal just when you change over to the course feed it gets a...
  19. Replies
    11
    Views
    2,146

    i hope these pics load

    i hope these pics load
  20. Replies
    11
    Views
    2,146

    Standard Modern 1340 lathe question

    Good morning folks,I have a question about my standard modern lathe,I hope its okay to ask it here.My machine has a leadscrew and feed rod.Both turn when using feed on carriage.I was wondering if...
  21. Replies
    17
    Views
    3,006

    Sent you a pm

    Sent you a pm
  22. Replies
    3
    Views
    972

    Looks like 6 7/8" from top to centerline

    Looks like 6 7/8" from top to centerline
  23. Replies
    3
    Views
    972

    Forgot all about these ,They measure 6 1/16 from...

    Forgot all about these ,They measure 6 1/16 from the bottom of the dovetail to centerline of 2 1/8" bore.Hope this helps.
  24. Replies
    99
    Views
    24,591

    congrats thats a nice lathe,i have the 2013/17...

    congrats thats a nice lathe,i have the 2013/17 also made in 1968.It swings 24 5/8 on the tag but it will swing 26.Its also 174" c to c.Thought I would mention that mine has a 15 horse motor and...
  25. Not sure about the 5 HP mill vertical head ,the...

    Not sure about the 5 HP mill vertical head ,the #2 lite version drives directly off the spindle keys,no gear.
Results 1 to 25 of 145
Page 1 of 6 1 2 3 4