Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Ken hosford

Page 1 of 12 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    3
    Views
    199

    granite 48 x 96 x 15 Mitutoyo

    base from large CMM Stupid heavy 10000 lbs has been stored outside some mistreatment evident $1500 buy responsible for arranging loading and trucking located in Dexter Michigan
  2. Replies
    1
    Views
    182

    I was in TK Atlas They make JD and Cat cranks ...

    I was in TK Atlas They make JD and Cat cranks There final polish was with what they were calling micron belts I believe 1500 grit
  3. Just to trow a wrench into this Belleville...

    Just to trow a wrench into this
    Belleville washers are a spring like no other the farther you compress the rate drops of and eventually the flip
    I found out about this on some torque limiters...
  4. Replies
    12
    Views
    762

    i believe you will find McMasterCarr has it

    i believe you will find McMasterCarr has it
  5. Thoughts on tightening like a mother Mill...

    Thoughts on tightening like a mother

    Mill tables droop not because gravity has pulled them down or they were over loaded .
    mill tables get peened into warped state, the bottom side of the tee...
  6. Tolerance on od? punched giving a od on one face...

    Tolerance on od? punched giving a od on one face smaller than od on other ? nib ? center of punch on no flat punch lastly tolerance on thickness ?
  7. Those boxes like the flat head have mostly left...

    Those boxes like the flat head have mostly left us for better or worse
  8. Larry is right

    Larry is right
  9. I have 3ph on a old farm my power drops to often...

    I have 3ph on a old farm my power drops to often ? once a month ? I tellby having to reset silly digital clocks micro waves stoves water softeners etc ( DTE )
  10. Replies
    2
    Views
    694

    I can not tell you much you have told me more...

    I can not tell you much you have told me more than i new as far as it being a Lima unit
    I have same motor gearbox assy on a converted from line shaft throatless shear neat units I would change...
  11. Replies
    31
    Views
    1,636

    Those are sold as dreams wishes and prayers ...

    Those are sold as dreams wishes and prayers
    Only if the bolt is not bottomed or rusted solid will screwing in a slow tapered wedge which will make the bolt tighter ever remove it .
    To think a...
  12. I am partial to Kluber lube rolling element lube ...

    I am partial to Kluber lube rolling element lube there are a number of different ones for different needs
  13. Replies
    14
    Views
    1,152

    Motor shaft will typically have a larger bearing...

    Motor shaft will typically have a larger bearing than the out put shaft leaving a shoulder you peen this in the corner on the smaller dia section using a rounded cold chisel
    you straighten...
  14. Shaft like that are canidates for peening...

    Shaft like that are canidates for peening straight You take a cold chisel and round the end you peen on the inside corner of the transition radius to the shoulder with hardened components it can...
  15. Replies
    9
    Views
    1,067

    Google is your friend I do not know were but they...

    Google is your friend I do not know were but they are out there but what I am here to say is with a little care you can do it your self I have many times in a pinch . you want pink or white ...
  16. Replies
    7
    Views
    1,437

    Kissler makes nice ones

    Kissler makes nice ones
  17. you can buy just the rolling element for those...

    you can buy just the rolling element for those and reuse the mount .
  18. Replies
    6
    Views
    856

    that is a job for a shaper and you will have to...

    that is a job for a shaper and you will have to make a one sided knurl tool and flip it to get to each side
  19. Thread: honing

    by Ken hosford
    Replies
    7
    Views
    993

    what is the length of thw bore

    what is the length of thw bore
  20. Pexto built a roller for doing production high...

    Pexto built a roller for doing production high tolerance rolling
    Very simple 2 roll bender Bottom roll urethane top roll under size to give room for over bend , lower roll powered slowly upper...
  21. Replies
    1
    Views
    588

    to me it looks like some did not have the correct...

    to me it looks like some did not have the correct motor and made a jack shaft and motor mount missing motor
  22. Presumably it has a hollow stem for valve stems ?

    Presumably it has a hollow stem for valve stems ?
  23. To Play with ? what is fun worth ? as in...

    To Play with ? what is fun worth ? as in production or 1 of machining most likely you will be so far behind a cnc machine it is cheaper to farm it out for commercial purposes.
    What a guy can do...
  24. Replies
    15
    Views
    2,536

    absolutely cool you are an inspiration

    absolutely cool you are an inspiration
  25. Replies
    162
    Views
    13,015

    Primary Reason for me $$$ Living in Michigan ...

    Primary Reason for me $$$ Living in Michigan heating cost are real . Money spent on heat has no lasting affect . That money spent on tooling , machinery or materials I have something in the future...
Results 1 to 25 of 299
Page 1 of 12 1 2 3 4