Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Phil in Montana

Page 1 of 57 1 2 3 4

Search: Search took 0.02 seconds.

  1. Its not delta, special y , or scott conn like...

    Its not delta, special y , or scott conn like sparky said...It will work for you...Phil
  2. Replies
    51
    Views
    2,518

    Its easy, when the hub is in the lathe use a...

    Its easy, when the hub is in the lathe use a sharp point tool and scribe the bolt hole ring (5 1/2 inch for 5 on 5 1/2 pattern) this is to check your work when you drill your holes....center the bore...
  3. Replies
    14
    Views
    745

    I test ran a 16v92 a few years back with no...

    I test ran a 16v92 a few years back with no exhaust... meet people that lived 1 mile away and none were happy...Phil
  4. Replies
    14
    Views
    745

    Boy the house next door would like that...Phil

    Boy the house next door would like that...Phil
  5. Replies
    14
    Views
    745

    Gen set does work BUT, a 30kw will cost 6 bucks...

    Gen set does work BUT, a 30kw will cost 6 bucks an hour for fuel, needs oil changes, makes noise and ugly smoke, and will weer out...Phil
  6. Replies
    16
    Views
    1,097

    Might start with the common name, Pelton...

    Might start with the common name, Pelton Wheel...phil
  7. all bobcats take the same key, 7000lbs... dove...

    all bobcats take the same key, 7000lbs... dove its self away...Phil
  8. Help nothing to do with machine work just saport equipent...Phil

    Last night some one cut my fence and stole my 853h bobcat in Missoula, mt. If any of you see a 853h for sell drop me a line. Most will be legit, but maybe I will get lucky...Thanks Phil... If this is...
  9. What a deal... should be here in Montana...Phil

    What a deal... should be here in Montana...Phil
  10. I can not see anyway that the machine can pay its...

    I can not see anyway that the machine can pay its way, going to be a money pit to load, move and unload...Phil
  11. Very little, the damage that grease on the...

    Very little, the damage that grease on the brushes will do is ugly...1 pump every 2 years...Phil
  12. Raise the price until he see,s the light...Phil

    Raise the price until he see,s the light...Phil
  13. You have picked a bad span, 60 ft with steel...

    You have picked a bad span, 60 ft with steel truss will work or your 70 ft with center posts (I know that sucks) wood truss,s will never work if you have snow load...Phil
  14. You have picked a crappy size, the span is a deal...

    You have picked a crappy size, the span is a deal breaker. The building would be a lot cheaper with center posts (I know that sucks)or a 60 ft span with steel truss,s. With any type snow load wood...
  15. Polish the spindle to remove the highs spots...

    Polish the spindle to remove the highs spots only, a new oil stone works good for this with the spindle in a different lathe. remove some shims but not all, and use a sunnen hone to clean up your...
  16. Done both.. GO with metal,...Phil

    Done both.. GO with metal,...Phil
  17. Replies
    67
    Views
    6,089

    Never, fire the bum...Phil

    Never, fire the bum...Phil
  18. It will bend easy, but the bar will not be sqr in...

    It will bend easy, but the bar will not be sqr in the cross section of the bend, will probably deform a 1/8 inch top to bottom with a 4 inch rad, like a trapezoid...Phil
  19. thermite....Shame on you undercutting is done on...

    thermite....Shame on you undercutting is done on all large dc motors STILL, only starter motors are not undercut.. The hard copper brushes rub the mica away. Everything else is undercut with carbon...
  20. Use the 409 sliting stone (1 inch di) and a 402...

    Use the 409 sliting stone (1 inch di) and a 402 arbor. works good.... the ez409 is too big...Phil
  21. Use a dermal grinder and 409 slitting stones,...

    Use a dermal grinder and 409 slitting stones, then grind 2 hack saw blades to a right and a left hook tool to de-burr...Phil
  22. I would vee the rod end down about 1/2 inch to...

    I would vee the rod end down about 1/2 inch to make more room for the welds and pre and post heat the welds. If the eye breaks the weld you meet lawyers...Phil
  23. Man up and use the contact cement, Its not hard...

    Man up and use the contact cement, Its not hard to set the sheet just right. Put a stop blocks on the long side and hinge the sheet down...easy...Phil
  24. Replies
    2
    Views
    456

    I like the deep rust adds value...Phil

    I like the deep rust adds value...Phil
  25. Be glad you dont have 3 phase, with 3 phase you...

    Be glad you dont have 3 phase, with 3 phase you pay more for the kwa, have a demand charge, more intense electrical inspections,you must comply with zoning, and pay for the power to be brought in....
Results 1 to 25 of 1404
Page 1 of 57 1 2 3 4