Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: wagoneer1

Page 1 of 3 1 2 3

Search: Search took 0.00 seconds.

  1. Book Lot B

    I’d like to buy Lot B, thanks.
  2. Replies
    22
    Views
    4,579

    Cerakote Coatings (https://www.cerakote.com/)

    Cerakote Coatings
  3. Replies
    12
    Views
    1,009

    Tried sending a PM but your inbox is full. Please...

    Tried sending a PM but your inbox is full. Please PM me with how to pay you.

    Thx
  4. Replies
    12
    Views
    1,009

    PM sent - I’ll take it.

    PM sent - I’ll take it.
  5. Sent a PM regarding the Jacobs 8-1/2N. Rgds

    Sent a PM regarding the Jacobs 8-1/2N.

    Rgds
  6. Replies
    25
    Views
    4,008

    NAS1102 is another series with a 100 deg head....

    NAS1102 is another series with a 100 deg head. Comes in a variety of strength levels.
  7. Replies
    3
    Views
    629

    Yes. Solution treat and age IAW AMS2770 or...

    Yes. Solution treat and age IAW AMS2770 or industry appropriate equivalent.
  8. I'd recommend spinodally hardened bronze....

    I'd recommend spinodally hardened bronze. Toughmet3 aka AMS4596 or AMS4597 (highest strength). I use this in very demanding aerospace applications. I wouldn't recommend mg-bronze for that...
  9. Replies
    4
    Views
    1,335

    I'll take it. Please PM me with payment details.

    I'll take it. Please PM me with payment details.
  10. Replies
    12
    Views
    1,850

    D2. Temper at 950 degrees F for 58-60 HRC.

    D2. Temper at 950 degrees F for 58-60 HRC.
  11. Replies
    16
    Views
    1,840

    Bent-axis rotating group and cylinder block. Most...

    Bent-axis rotating group and cylinder block. Most likely a hydraulic motor. Looks like an old Vickers design.
  12. Replies
    31
    Views
    6,685

    Interested in the SB 10 collet rack, with some...

    Interested in the SB 10 collet rack, with some collets and tube if it's for a 10K as it appears in the picture. PM sent.

    Thanks!
  13. Replies
    3
    Views
    1,192

    Would you sell me just the small shaper tool; 5th...

    Would you sell me just the small shaper tool; 5th one down on left not counting the rocker posts?
  14. Replies
    50
    Views
    16,010

    Have interest in the 18" casting but price...

    Have interest in the 18" casting but price dependent, of course..
  15. PM sent. Waiting for a response.

    PM sent. Waiting for a response.
  16. Replies
    10
    Views
    2,847

    Ahhhh - it's a Hjorth...not a Rivett. Perhaps...

    Ahhhh - it's a Hjorth...not a Rivett. Perhaps I've missed something - LOL. Best wishes.
  17. C1117 has been used for solenoids.

    C1117 per ASTM A108, annealed.
  18. Aluminum Pin

    For these circumstances I've used 6061-T6 pins that are Type III hard coated. Steel can be made to work with judicious tolerancing. Be sure to adequately countersink or counter bore the press fit...
  19. Replies
    7
    Views
    2,616

    I'd be using a #39 drill prior to reaming.

    I'd be using a #39 drill prior to reaming.
  20. Replies
    1
    Views
    1,423

    PM sent your way, Ed. J

    PM sent your way, Ed.

    J
  21. I received the 3S yesterday in fine shape. It is...

    I received the 3S yesterday in fine shape. It is in essentially like new condition.
    Thanks Mike!!!
  22. Replies
    11
    Views
    2,470

    Looks like a Burke #4

    It reminds me of a Burke #4.
  23. Replies
    45
    Views
    6,371

    A Good American

    God bless you, Sir! Amen.
  24. Replies
    6
    Views
    2,106

    Profile Tolerance

    Where the .005 tolerance zone is distributed wrt the 60.00 basic depends upon whether it is unilaterally or bilaterally applied.
  25. Replies
    14
    Views
    6,754

    Perfectly fine callout

    It's telling you the length of the chamfer. Perfectly fine callout; remember that the length of the "sides" of a 45 degree chamfer are equal.
Results 1 to 25 of 70
Page 1 of 3 1 2 3