Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Simple Machinist

Search: Search took 0.00 seconds.

  1. Replies
    7
    Views
    1,289

    SUCCESS!! After receiving a 512 ohm resistor...

    SUCCESS!! After receiving a 512 ohm resistor (pictured earlier) from Mouser Electronics, skip0 is receiving the 24v stop signal, the machine is beeping and the tool offsets are being set via the tool...
  2. Replies
    7
    Views
    1,289

    284184284185 Does this look right? PM me if it...

    284184284185

    Does this look right? PM me if it looks right, I'd love to fix this. I've got tape on the arm because it was returning too far into the pocket (I pulled the old lip seal so I could...
  3. Replies
    7
    Views
    1,289

    Just when you think you are out!!! I connected...

    Just when you think you are out!!! I connected the wires noted in my last post and I'm getting voltage back to TB3 TL, but I'm not getting voltage to Skip 0 required for the tool measure ladder....
  4. Replies
    7
    Views
    1,289

    I think it's going to shape up to be really...

    I think it's going to shape up to be really simple. The electrical drawing shows the tool setter circuit running from TB3 24+ to TB3 TL. There wasn't continuity across this circuit, so I followed the...
  5. Replies
    7
    Views
    1,289

    1986 QT-10N Tool Setter Beep

    I've got a 1986 QT-10N, 20 HP, 12 position turret with the tailbody (universal). When the tool setter extends on the tool measure command, it does not beep. it also does not enter a value when you...
  6. Replies
    21
    Views
    2,191

    I did not have the board hooked up when I read...

    I did not have the board hooked up when I read the voltages from the supply. I couldn't understand how the board could read status of the NC and switch LED's (and not be too damaged to function) if...
  7. Replies
    21
    Views
    2,191

    Update: I found the purchased parts manual in...

    Update:

    I found the purchased parts manual in my set that covered the FR-SE Drive. Went through the troubleshooting, found that the power supply is not right. I'm getting 9.8v AC from every pin in...
  8. Replies
    21
    Views
    2,191

    X031 description is NFB Trip...Is NFB and...

    X031 description is NFB Trip...Is NFB and abbreviation for a drive or machine component?

    242136
  9. Replies
    21
    Views
    2,191

    Is it possible that the top red LED on the...

    Is it possible that the top red LED on the vertical strip to the left of the lower drive board (pictured) is burnt out, or just not functional? When I press the reset button, all of the green lights...
  10. Replies
    21
    Views
    2,191

    I didn't realize it until tonight, but the ladder...

    I didn't realize it until tonight, but the ladder diagram is there (I've only got a digital copy of the drawings). I've been studying the ladder, the connector diagrams and everything in between......
  11. Replies
    9
    Views
    3,208

    Is there a guide to parameters so you know what...

    Is there a guide to parameters so you know what they apply to? Some of mine are defined in the electrical drawing set, but many are not.
  12. Replies
    21
    Views
    2,191

    I pulled the cover off of CND 2 going into the...

    I pulled the cover off of CND 2 going into the NC, Pin 11 is receiving 24v from Con. 3(Pin 18) at the drive. The drawing also references pin 20 on the CND 2 connector, but that location is not wired....
  13. Replies
    21
    Views
    2,191

    Thanks a lot for the help. I'll pin down whether...

    Thanks a lot for the help. I'll pin down whether or not I have the voltage at pin 18 some how, I'm just trying to find out if my problem is on the drive side or the NC side (like maybe a bad...
  14. Replies
    21
    Views
    2,191

    I really appreciate the feedback from you both. ...

    I really appreciate the feedback from you both.



    Do you know how many volts the "LOGIC ONE" Signal should be?


    Also, Just so I'm reading the electrical drawings correctly, if there is no...
  15. Replies
    21
    Views
    2,191

    Quick Turn 10n Spindle Issue

    I'm working on bringing up a 1986 Quick Turn 10n/ T-2 control. Everything works fine (Servos, Turret, Robot Tool Measure Arm, Hydraulics, Tail Stock) except the spindle. When I try to run the spindle...
Results 1 to 15 of 15