Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Tedger

Page 1 of 6 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    111
    Views
    6,380

    I'm not familiar with any you mention here but...

    I'm not familiar with any you mention here but hopefully you can find someone who is. My biggest worry would be support. Do they have people in your area that can help you out if needed or do you...
  2. Confirmed case's refers to people who got tested...

    Confirmed case's refers to people who got tested because they were sick enough to warrent a Covid-19 test. I know a few people here in the states who called their doctor when they felt ill and were...
  3. Replies
    8
    Views
    999

    Yes. I don't remember whether the signal go's...

    Yes. I don't remember whether the signal go's high(+24VDC) or go's low (0v) when it changes state but it sounds like the switch is working.
  4. Replies
    8
    Views
    999

    The sensor has 3 wires. Blue is Earth, Brown is...

    The sensor has 3 wires. Blue is Earth, Brown is Positive 24V DC. Black is the signal Wire. With the machine powered up,You can use a multi meter to check the signal on the black wire when you...
  5. Replies
    8
    Views
    999

    It sounds like your sensors are working good....

    It sounds like your sensors are working good. Perhaps your problem is with the relays and contactors that operate the turret motor in both directions.
    I am not familer with your brand of machine but...
  6. Replies
    8
    Views
    999

    When the index pin is energized. it gets pulled...

    When the index pin is energized. it gets pulled down into a slot on the large rotating cam in the turret. There is a sensor inside the turret that senses when the pin is all the way engaged and that...
  7. Replies
    42
    Views
    3,126

    Diezul Clips should go into the secong groove...

    Diezul
    Clips should go into the secong groove down.( The shallow one)It's a bear sometimes to get them in but make sure they are seated before you put it all back together.
  8. Replies
    10
    Views
    1,655

    The tech didn't save the parameter changes in a...

    The tech didn't save the parameter changes in a new file? Ugh....
    I sent you a PM along with my Phone number. Take a look and get back to me.
    Thanks
  9. Replies
    10
    Views
    1,655

    You should have a copy of the NC and PLC files...

    You should have a copy of the NC and PLC files loaded onto your hard drive when the lathe left the factory. These can be reloaded into the machine to restore the parameters. This needs to be done if...
  10. Replies
    3
    Views
    526

    Depending on your year, You may not have brushes....

    Depending on your year, You may not have brushes. 95 and up came with AC motors I believe. You probably have either a motor problem or an amplifier problem. All three motors and all three amps are...
  11. Replies
    18
    Views
    1,994

    Swap the x axis motor for the z axis motor and...

    Swap the x axis motor for the z axis motor and see if the problem follows the motor. You can also do the same with the amplifier
  12. It's just the locating pin for the tool. It also...

    It's just the locating pin for the tool. It also is used for coolant depending on what machine you have. You could easily make a replacement but you can also contact Macoser for parts. 704-392-0110...
  13. Replies
    2
    Views
    979

    It looks like a Speedaire 5Z405 10 hp compressor...

    It looks like a Speedaire 5Z405 10 hp compressor pump
  14. Replies
    5
    Views
    1,000

    Those inserts fit the Valenite VWDR drills in the...

    Those inserts fit the Valenite VWDR drills in the following series;

    VWDR 100 125 454* 2.521 1.000
    VWDR 106 125 472* 2.521 1.062
    VWDR 112 125 495* 2.521 1.125
    VWDR 118 125 511* 2.521 1.187 ...
  15. Replies
    13
    Views
    1,600

    Ahh. I didn't read the post correctly.

    Ahh. I didn't read the post correctly.
  16. Replies
    13
    Views
    1,600

    Bob's method works on the 4020's but I've never...

    Bob's method works on the 4020's but I've never tried it on a VMC15. Just remember you will have to manually swap tools cause your spindle will move to a higher spot for a tool change.
  17. Replies
    14
    Views
    1,898

    Looks like a stone dresser

    Looks like a stone dresser
  18. Replies
    10
    Views
    1,655

    They have conversational programming but the...

    They have conversational programming but the Hyundai manuals aren't as helpful as they could be. I wouldn't say it's a hard control to learn,just different. Plenty of support if you need it so don't...
  19. Replies
    10
    Views
    1,655

    We have three of these lathes, all built around...

    We have three of these lathes, all built around 1999/2000. They are all 840D Siemens components. I've had to replace or repair a few drives over the years but there was never a problem finding...
  20. Replies
    50
    Views
    6,660

    The Heating element is a Regen resistor or also...

    The Heating element is a Regen resistor or also called a dynamic braking resistor. It helps slow down the spindle quickly by absorbing the energy the spindle motor is dumping to slow down. I've never...
  21. There should be a transformer wiring chart in the...

    There should be a transformer wiring chart in the cabinet where the transformer lives.Check your incoming voltage and set it to the specs on the chart. If your getting 245V-250V between legs, I would...
  22. Replies
    2
    Views
    585

    atmo, I replied to your PM. Just send me a good...

    atmo, I replied to your PM. Just send me a good email and I'll send the Manual PDF.
    Thanks
  23. Replies
    2
    Views
    585

    I have some experiance with this system. What...

    I have some experiance with this system. What issues are you having? PM me and I'll send you a pdf of the manual.
  24. Replies
    16
    Views
    1,722

    Zoro sells one about that long for under $40....

    Zoro sells one about that long for under $40. Made by True Temper but I'm not sure of the actual quality.
    EDIT: Looks like Amazon does also under the AME's brand
  25. Replies
    64
    Views
    4,441

    You type "SETTO" from the command line and...

    You type "SETTO" from the command line and designates where it's at at that moment as tool 1. Type "UT,2" and hit the green button and it should load tool 2. You need to address the Y axis alarm...
Results 1 to 25 of 128
Page 1 of 6 1 2 3 4