Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: BugRobotics

Page 1 of 17 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    1
    Views
    157

    I have a Gorton I22 Mastermil and love it. ...

    I have a Gorton I22 Mastermil and love it. Heavier than a Bridgeport. Head doesn't nod forward like the Bridgeport. Quality machine.
  2. I'm going to pass on these. Thanks.

    I'm going to pass on these. Thanks.
  3. Replies
    10
    Views
    512

    Just heard back from Walter in Germany. The...

    Just heard back from Walter in Germany. The collets used are 161E dead length collets. He mentioned originally purchased from Ortlieb.
  4. Replies
    10
    Views
    512

    Thanks for the link Andy. I've visited that link...

    Thanks for the link Andy. I've visited that link but without the dimensions from the seller I'm just guessing. Using the one pic of the collet I have B42 may be too long.
  5. Replies
    10
    Views
    512

    Thanks Andy! Much appreciated.

    Thanks Andy! Much appreciated.
  6. Replies
    10
    Views
    512

    The collet size may be B42 judging by this post...

    The collet size may be B42 judging by this post by sfriedberg:
    FS Collet Chuck Walter Dividing Head
  7. I may be interested in the lot. Trying to...

    I may be interested in the lot. Trying to determine if they will fit a piece of equipment.
  8. Good deal, thanks. I'd want it shipped in the...

    Good deal, thanks. I'd want it shipped in the box. And since you brought up the extra insurance, if I say no then the item will arrive destroyed so lets throw an extra $50 on the insurance.
  9. I'll take L if it isn't spoken for.

    I'll take L if it isn't spoken for.
  10. Replies
    10
    Views
    512

    Yea, I couldn't find anything either. This is on...

    Yea, I couldn't find anything either. This is on eBay. Trying to get the seller to take measurements. Seller said the collets are "like" Brown and Sharpe collets. Here is a side view of the...
  11. Replies
    10
    Views
    512

    Of...

    Of course...https://uploads.tapatalk-cdn.com/20191019/48baad2cee5ef1f2874e2c25e3940e7f.jpg
  12. Received, thanks lazz!

    Received, thanks lazz!
  13. Replies
    10
    Views
    512

    Collets for Walter Indexer VT II W

    I'm looking for the collet type used with the Walter VT II W indexer. Any info is appreciated. Thanks.
  14. Replies
    28
    Views
    1,729

    Great point and totally agree that it's not the...

    Great point and totally agree that it's not the end all be all of serial tests. Like you mentioned voltage levels can be a big deal as well as total capacitance of the cable run but that's getting...
  15. Replies
    28
    Views
    1,729

    Yea, not hard at all. Disconnect the serial...

    Yea, not hard at all. Disconnect the serial connector from the machine and jumper RX and TX (usually pin #2 and #3 on a DB9 or DB25 connector). Then use Putty to start a serial connection
    ...
  16. Replies
    28
    Views
    1,729

    Have you performed a loopback test (mentioned by...

    Have you performed a loopback test (mentioned by corednc in post #5) with your current setup? If the loopback test works you can know you have good communication out and back into the computer...
  17. Replies
    28
    Views
    1,729

    My guess is the RS232 IC is fried on the inputs. ...

    My guess is the RS232 IC is fried on the inputs. I've successfully repaired this fault on my own machine by replacing this IC. Usually a single chip transceiver directly attached to the RX and TX...
  18. I'll take 1A, 3B, 3D, 3E, 3F. Thanks.

    I'll take 1A, 3B, 3D, 3E, 3F. Thanks.
  19. Replies
    7
    Views
    371

    Just to clarify...SPFPO or SDFPO? If it's...

    Just to clarify...SPFPO or SDFPO?

    If it's SDFPO (looks to be the standard prefix) this appears to be a new board. Offer $450 (or whatever you deem appropriate) and go from there. It has a 30...
  20. Replies
    7
    Views
    371

    Did a quick search on eBay and there were a...

    Did a quick search on eBay and there were a number of boards available.
  21. Replies
    3
    Views
    654

    I'll take em. PM incoming.

    I'll take em. PM incoming.
  22. I would go and download the user manuals from PC...

    I would go and download the user manuals from PC software and manuals

    Here is the service manual to get you started:
    TNC 145 Service Manual

    NOTE: Some of the German versions have better info...
  23. I'd try and get it working. That control is...

    I'd try and get it working. That control is solid. Heidenhain has been very helpful in the past when I've asked specific questions.

    What is the failure mode of the monitor? Do you have a scope...
  24. I'll take it. PM incoming.

    I'll take it. PM incoming.
  25. Replies
    2
    Views
    542

    I'll take em. PM incoming.

    I'll take em. PM incoming.
Results 1 to 25 of 424
Page 1 of 17 1 2 3 4