Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: hammer1092001

Search: Search took 0.00 seconds.

  1. Replies
    32
    Views
    1,694

    Cutters arrived. Seem to be good quality. Checked...

    Cutters arrived. Seem to be good quality. Checked them against the gears in my lathe to verify they are right. Perfect fit. And the set is complete
  2. Replies
    32
    Views
    1,694

    Found the cutters on ebay. Comming out of russia....

    Found the cutters on ebay. Comming out of russia. Sure they won't be here anytime soon. But I am in no hurry just picking away at it
  3. Replies
    32
    Views
    1,694

    The source? The gentleman in Sweden I received...

    The source? The gentleman in Sweden I received the information from? Or the source where I found the cutters to make the gears?
  4. Replies
    32
    Views
    1,694

    Thank you. They do cover a few of the gears I...

    Thank you. They do cover a few of the gears I need. But unfortunately not all of them. Right or wrong.,since I found and purchased a set of module 1.25 cutters ,I may as well make them all while...
  5. Replies
    32
    Views
    1,694

    Thanks for options. I ended up ordering a set of...

    Thanks for options. I ended up ordering a set of mod 1.25 cutters,full set of 8 for entire tooth range. I will just make the change gears I need ,here and there as I go along. Or just do them all...
  6. Replies
    32
    Views
    1,694

    Thank you for clarifying. I got a similar answer...

    Thank you for clarifying. I got a similar answer from a gentleman in Sweden who just so happens to have the same machine and a manual he plans to send me the information from. He also pointed out I...
  7. Replies
    32
    Views
    1,694

    I did ty. After more cleaning and another look....

    I did ty. After more cleaning and another look. I did find the gear/tooth count needed. Machine has a 6 tpi lead screw. Gears I need for standard thread range are 30t,60t,92t and 96t. To do full...
  8. Replies
    32
    Views
    1,694

    Luckily I have a fwd/rev lever for feed. So if...

    Luckily I have a fwd/rev lever for feed. So if the idler solves the gear ratio issue for threading,I can correct feed direction with the flip of a lever
  9. Replies
    32
    Views
    1,694

    Feed knobs show metric and imperial markings....

    Feed knobs show metric and imperial markings. Which would suggest to me it was intended for use in the U.S. though still equipped with a non traditional (by U.S. standards)550v motor
  10. Replies
    32
    Views
    1,694

    Thanks. I am "chasing threads" and have been...

    Thanks. I am "chasing threads" and have been fortunate enough to have found some great people willing to share information on this. Though google searching has proved less than bountiful on...
  11. Replies
    32
    Views
    1,694

    That would be great. Maybe the 127 tooth for...

    That would be great. Maybe the 127 tooth for metric just gets moved into an idler position for imperial. Thanks for the suggestion. Will look into that when I get it going. If it will fit in that...
  12. Replies
    32
    Views
    1,694

    That was kinda where I was heading. The machine...

    That was kinda where I was heading. The machine was in suck good shape I chose to strip it down and "restore" it. New paint,polish the ways. Just make it look as good as the shape it is in. When...
  13. Replies
    32
    Views
    1,694

    It has the chart with letters (a.b.c.d)...

    It has the chart with letters (a.b.c.d) designating the change gears. Had to count the teeth myself. Goes something like this. 24 tooth at spindle driving an 80 tooth idler which then drives a 127...
  14. Replies
    32
    Views
    1,694

    I can determine the pitch. That's the easy part....

    I can determine the pitch. That's the easy part. Just hoping someone may know more about these machines than I do or can find online,that may have the tooth count without all the math and ratio...
  15. Replies
    32
    Views
    1,694

    E3N-01 Kart lathe change gears

    I have recently aquired an E3N-01 lathe. Immaculate shape,tight screws and ways look brand new under slight surface rust from sitting. Unfortunately the machine came with only the metric change gears...
Results 1 to 15 of 17