Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Cal Haines

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    8
    Views
    709

    For masking holes, I make round pieces of masking...

    For masking holes, I make round pieces of masking tape, using round hole punches and a punch similar to this one: link. The trick is to stick the masking tape to a piece of wax paper before you try...
  2. Replies
    12
    Views
    1,391

    What does Tim charge for his conversion? By...

    What does Tim charge for his conversion?

    By the way, For Monarch 10ee Lathe has nice solid state modules that would also make you tubeless with the original DC drive.

    Cal
  3. Replies
    1
    Views
    258

    WiaD (Works in a Drawer) machines use the same DC...

    WiaD (Works in a Drawer) machines use the same DC panel and specify a 1A fuse in that location. Punch in the diameter, length, etc. in to the selector at McMaster-Carr (link) to find a compatible...
  4. Replies
    12
    Views
    1,391

    Try this guy: Tas Iron Ltd...

    Try this guy: Tas Iron Ltd. Ask for Tim. He's a machinery rebuilder near Cleveland and usually has 10EE motors to sell.

    Cal
  5. Thread: Lubes

    by Cal Haines
    Replies
    3
    Views
    251

    Make sure you read post #11...

    Make sure you read post #11.

    Cal
  6. Replies
    12
    Views
    1,391

    For your '73 what? 10EE? Something else? What...

    For your '73 what? 10EE? Something else? What kind of motor? DC motor?

    Cal
  7. A & B are armature contacts. C and D are not...

    A & B are armature contacts. C and D are not field contacts. C controls power to the generator rheostat and thus the generator's field windings. D keeps the main contactor coils energized when the...
  8. Try this guy: 10EE motors on Ebay...

    Try this guy: 10EE motors on Ebay
    He's a machinery rebuilder in Ohio. He was reported to have DC panels for sale.

    Cal
  9. Replies
    10
    Views
    3,242

    It sounds like something else is going on with...

    It sounds like something else is going on with reverse. What do you mean "Reverse will work if I jump the circuit"? Where are you placing the jumper?

    Cal
  10. Replies
    9
    Views
    775

    There are very few round-dial assembly drawing...

    There are very few round-dial assembly drawing floating around and I am not aware one for the ELSR. As far as I know, Monarch didn't prepare exploded drawings of anything. The closest thing to that...
  11. As far as I know, the dowel pins and taper pins...

    As far as I know, the dowel pins and taper pins were match drilled once the assembly had been aligned to the machine. Your machine probably never had the a taper attachment (TA), which is good for...
  12. Replies
    4
    Views
    630

    Hal, Thanks for pointing that out. The problem...

    Hal,

    Thanks for pointing that out. The problem comes from trying to insert new links into the sticky page. Sometimes odd things happen and I don't always catch them.

    Cal
  13. Replies
    9
    Views
    775

    As I've told you several times before, I don't...

    As I've told you several times before, I don't think that you're missing anything (assuming that you haven't lost any parts). What you're missing is an understanding of how this switch works. I have...
  14. Replies
    12
    Views
    1,234

    There is a drawing, but it's in really rough...

    There is a drawing, but it's in really rough shape, sections are missing and some parts are illegible. It does show the area in question. What is shown is a setscrew, spring and plunger. The same...
  15. Replies
    27
    Views
    1,958

    Brian, It's from a square-dial DC control...

    Brian,

    It's from a square-dial DC control panel with a Cutler-Hammer bulletin 598 contactor:
    335536
    Square-dial 10EEs with motor/generator and WiaD (Works in a Drawer) drives, as well as some...
  16. I don't like using thread cutting taps and dies...

    I don't like using thread cutting taps and dies to chase threads. It's too easy to damage the threads. I've got a set of thread repair taps, dies and files that are perfect for this sort of thing....
  17. Replies
    162
    Views
    7,394

    It's been a long time since I messed with it, but...

    It's been a long time since I messed with it, but I think I replaced the washer on the screw end with one that has a smaller OD, so it still holds the felt disk, but won't hit the feed gear.

    Cal
  18. Replies
    162
    Views
    7,394

    That looks just fine. But you need to drop the...

    That looks just fine. But you need to drop the apron a bit for the washer to clear the cross-feed drive gear in the apron when you insert the screw.

    Cal
  19. Replies
    26
    Views
    2,396

    Very nice! If you don't mind saying, how much did...

    Very nice! If you don't mind saying, how much did that cost?

    Cal
  20. Replies
    162
    Views
    7,394

    Might need to rock the leadscrew back and forth...

    Might need to rock the leadscrew back and forth to engage it.

    Cal
  21. Replies
    162
    Views
    7,394

    On newer round-dials with the lever-type gearbox...

    On newer round-dials with the lever-type gearbox (instead of the T-handle) the gearbox outputs can be disengaged via the lever.

    What do you mean "lower knob"?

    Any time there's a problem getting...
  22. Replies
    162
    Views
    7,394

    On round-dials, yes. Cal

    On round-dials, yes.

    Cal
  23. Replies
    268
    Views
    40,391

    No, I've never removed a link.I've only edited a...

    No, I've never removed a link.I've only edited a few dozen posts for photos and most of them were mine. I've replaced PhotoBucket links with PM hosted photos where I have the original photos or could...
  24. Replies
    162
    Views
    7,394

    I don't know, but the first generation parts seem...

    Cal, what is different about the Sundstrand worm gear? I've had mine apart, but I did not try to interchange any parts, and it looked the same as other 10EE's[/QUOTE]
    I don't know, but the first...
  25. Replies
    162
    Views
    7,394

    The 10EE feed-rod worm gear (part EE-2106) is the...

    The 10EE feed-rod worm gear (part EE-2106) is the same for most round- and square-dials, with the possible exception of the Sundstrand drive machines. Square-dial parts sheet 147 shows the worm,...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4