Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: gbent

Page 1 of 60 1 2 3 4

Search: Search took 0.06 seconds.

  1. Replies
    3
    Views
    292

    The large components of value are condition of...

    The large components of value are condition of the ways, condition of the spindle bearings, overall appearance, your ability to load a truck/trailer, and location. Give us some information on these...
  2. PM member Zahnrad Kopf has made these pinions in...

    PM member Zahnrad Kopf has made these pinions in the past. They are excellent. It is worthwhile to wait for him to make another run and buy one. Then, promise yourself you will never forget to...
  3. Replies
    15
    Views
    601

    DeVlieg made a range of "L" shaped adapters to...

    DeVlieg made a range of "L" shaped adapters to hold their cartridges for outside boring. Different holes in the base for rough adjustment. I don't think I've seen ones that would go 8" deep though....
  4. Thread: web straps

    by gbent
    Replies
    3
    Views
    295

    Twisted eye are better for a choker.

    Twisted eye are better for a choker.
  5. Replies
    66
    Views
    3,631

    You did it and were there, I was not. But I sure...

    You did it and were there, I was not. But I sure hate to see that sling against the feed rod. A piece of 2 x 4 packing to space the sling out would be safer.
  6. Replies
    5
    Views
    754

    I think they were called Rainbow. Not made for...

    I think they were called Rainbow. Not made for quite some time. I have a set on a vertical drill press and find them handy.
  7. Replies
    20
    Views
    1,230

    Of course you do! What a silly question to ask.

    Of course you do! What a silly question to ask.
  8. Replies
    27
    Views
    1,493

    Shipper is stupid. I'd not pay for that. The...

    Shipper is stupid. I'd not pay for that. The drill will rock back and forth a little, loosening the end boards on the pallet. Then, since the strapping is a little loose, it will rock a little...
  9. Replies
    4
    Views
    390

    See my post from last month. ...

    See my post from last month.

    https://www.practicalmachinist.com/vb/tooling-parts-and-accessories-for-sale-or-wanted/fs-aloris-da-toolpost-w-2-da2-holders-397305/?highlight=da+aloris
  10. Replies
    23
    Views
    1,132

    You aren't going to be burning 2" stock with a...

    You aren't going to be burning 2" stock with a plasma. You can easily burn 2" with O/A, so your control needs to be compatible with both. I have a similar situation where I'd love to have a CNC...
  11. Replies
    30
    Views
    1,533

    I agree with what you wrote, except for that...

    I agree with what you wrote, except for that part. A good braze joint is as strong as gray iron.
  12. How many folks here would like to find a guy who...

    How many folks here would like to find a guy who shows up every day, makes good parts, and does (nearly) exactly what he is told? The name is verboten now, but you have a "useful idiot". It is your...
  13. Replies
    14
    Views
    1,184

    Some folks are even making dies by 3d printing.

    Some folks are even making dies by 3d printing.
  14. Replies
    5
    Views
    485

    That happened because the previous owner started...

    That happened because the previous owner started cutting without tightening the stroke adjustment nut. There was a forum member that made some very nice replacements, maybe he will chime in and make...
  15. Yes, and lost in the news about the tragic New...

    Yes, and lost in the news about the tragic New York City apartment fire was another fire in New York City. The lost fire started in a restaurant where employees were charging electric bikes. One of...
  16. Replies
    103
    Views
    7,662

    If the space had been open for some time, your...

    If the space had been open for some time, your landlord may not have had much choice on renters. If you don't like your landlord now, wait until a bankruptcy trustee is your landlord.

    I have read...
  17. Replies
    30
    Views
    1,533

    You need the Paki fellow in the video from a post...

    You need the Paki fellow in the video from a post a few weeks ago, gas welding the cast iron engine block. Gas welding with cast iron filler will produce the best weld, if you can find someone who...
  18. Replies
    81
    Views
    5,794

    Unless you are doing some serious work consider...

    Unless you are doing some serious work consider just using air blast.
  19. Replies
    33
    Views
    1,858

    Its a very poor metaphor. There is no way you...

    Its a very poor metaphor. There is no way you can get 1045 that hard, just not enough carbon.

    Ox, how were the ends cut? I'm having a hard time imagining how they quenched a large piece of 1045...
  20. Replies
    13
    Views
    1,183

    You could pickle the scale to remove it.

    You could pickle the scale to remove it.
  21. I agree with the big nut and rattle wrench. I...

    I agree with the big nut and rattle wrench. I don't agree with a big breaker bar, it could put to much torque to the boiler. If the rattle wrench fails, I'd cut the top out of the dome. Then I'd...
  22. Replies
    77
    Views
    3,594

    That plastic mortar box will be ok if you repower...

    That plastic mortar box will be ok if you repower the lathe with a 2 hp motor. Even a 5hp will lay a pile of hot chips in the pan that will melt through in a couple of minutes.
  23. Replies
    11
    Views
    822

    Catalog size is swing over the cross slide,...

    Catalog size is swing over the cross slide, actual swing is over ways.
  24. Replies
    2
    Views
    296

    WTB Landis #10 chasers, holders

    Looking for chasers for a 10H Landis die head. Chaser holders as well. I am missing chasers for 7, 9, 12, 14, 24, and 32 tpi, and 1/4 and 1/2 npt. These chasers come in sets of 4, and are 15/16...
  25. Either grind a tool bit the proper size, or use a...

    Either grind a tool bit the proper size, or use a tool bit less than 1/2 the finish width. Plunge the full width in the proper position for either side, then come back and clean up the middle. If...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4