Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: icehd81

Page 1 of 25 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    19
    Views
    17,318

    What kind of stresses are involved between the...

    What kind of stresses are involved between the 1/4" screw and the 1/2" rod? Are you using a lathe to drill and tap? You might consider a tapping head if you are in a lathe, and depending on the...
  2. Replies
    6
    Views
    7,683

    Still listed in the current book, only not...

    Still listed in the current book, only not straight 140. There's Mobilube HD 80W-140 and Mobilube HD Plus 85W-140.
  3. Replies
    44
    Views
    26,367

    Epoxy is a beautiful thing until you spill oil....

    Epoxy is a beautiful thing until you spill oil. Then it's really hard to stand up.
  4. Replies
    4
    Views
    2,566

    It has always been our practice that when a...

    It has always been our practice that when a chamfer is angled from a specific plane it must have an angle dimension from that plane, as well as a length dimension of at least one leg. In many cases...
  5. Replies
    18
    Views
    2,902

    Finally

    [QUOTE=Bobw;851298]

    "STAINLESS!!!!!!!"

    My second biggest pet peeve next to "BILLET" or the French "BILLETTE". (how do you put that stupid little thing over the E?)

    Third would be "cold...
  6. Replies
    16
    Views
    9,474

    You wil need to have a stage 1 or stage 2 kit...

    You wil need to have a stage 1 or stage 2 kit installed, depending on the muffler you choose and how much baffling is involved. The dealer's techs can advise which you need. I run an aftermarket...
  7. Replies
    6
    Views
    1,582

    Does your quill use R-8 collets? If it does the...

    Does your quill use R-8 collets? If it does the ones you see on E-bay will work.
  8. Replies
    20
    Views
    9,422

    Pretty common. I've had the expensive to the...

    Pretty common. I've had the expensive to the cheap and they all seem to have some amount of runout. Probably has a lot to do with what position it is in when it is locked down on the arbor. They have...
  9. Replies
    8
    Views
    1,509

    How's the alignment? Is the belt tight? It's just...

    How's the alignment? Is the belt tight? It's just a simple step pulley arrangement. If everything is aligned and tight enough it should work the same as other speeds. Make sure your motor slides are...
  10. Replies
    21
    Views
    10,489

    I have a question rather than an answer. What are...

    I have a question rather than an answer. What are you doing for the other end to provide a non skid tip?
  11. Replies
    21
    Views
    4,646

    You live in florida and you're worried about...

    You live in florida and you're worried about having to park outside? Try Illinois in mid January.
  12. Replies
    7
    Views
    1,677

    Temperature control. That means the building must...

    Temperature control. That means the building must be well insulated, heated in the cold or cool months and cooled in the warm months. And the temperature control should operate 24 hours a day seven...
  13. Replies
    6
    Views
    1,139

    Delta

    Hi George, The Delta valve uses a ball for a mixer. It has holes that line up with ports in the ball cup inside. Spring loaded rubber seals ride against the ball. The holes in the seals are somewhat...
  14. Replies
    3
    Views
    5,809

    Most bearing catalogs provide that information....

    Most bearing catalogs provide that information. If not Machinery's Handbook will provide transition location tolerances in the limits and fits section.
  15. Replies
    5
    Views
    1,264

    Thanks guys

    I do have Vickers conversion on my chart, but it isn't shown in that fashion. Old International Harvesters chart.
  16. Replies
    5
    Views
    1,264

    Hardness conversion

    I have a french drawing that calls out a hardness of "750Hv 0.3". Anyone know what that is equivilent to on the Rockwell C scale, or a Brinell hardness?
  17. Replies
    51
    Views
    7,936

    Being a deisel I doubt it would stall out, but...

    Being a deisel I doubt it would stall out, but rather than spin you would probably break a track or some of the drive components.
  18. Replies
    25
    Views
    13,249

    Mobilgrease XHP222 is an extreme pressure...

    Mobilgrease XHP222 is an extreme pressure multipurpose lithium complex grease.
  19. Replies
    15
    Views
    2,281

    Thanks guys.

    Thanks guys.
  20. Replies
    15
    Views
    2,281

    Where is the best place on the base casting to...

    Where is the best place on the base casting to mount one of those Bridgeport collet racks? I don't want to just drill only to find out I picked a thin spot.
  21. Replies
    11
    Views
    934

    That is just awsome.

    That is just awsome.
  22. Replies
    10
    Views
    763

    I have 3 Pac rim power feeds of the Asong brand....

    I have 3 Pac rim power feeds of the Asong brand. One is on my Z feed and the other two are on the shelf, because the speed control lost the low speed. No problem if I could do everything at 3 feet...
  23. Replies
    10
    Views
    736

    I have 3 Pac rim power feeds of the Asong brand....

    I have 3 Pac rim power feeds of the Asong brand. One is on my Z feed and the other two are on the shelf, because the speed control lost the low speed. No problem if I could do everything at 3 feet...
  24. Replies
    26
    Views
    1,803

    It's China made, but not too bad in spite of...

    It's China made, but not too bad in spite of that. They have good power and are relatively accurate with the gibs properly adjusted. It's a bit difficult to adjust the tail stock unless you replace...
  25. Replies
    26
    Views
    1,803

    It's China made, but not too bad in spite of...

    It's China made, but not too bad in spite of that. They have good power and are relatively accurate with the gibs properly adjusted. It's a bit difficult to adjust the tail stock unless you replace...
Results 1 to 25 of 610
Page 1 of 25 1 2 3 4