Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: sirAIG

Page 1 of 8 1 2 3 4

Search: Search took 0.00 seconds.

  1. Replies
    2
    Views
    212

    If you're using that ball mill on relatively flat...

    If you're using that ball mill on relatively flat surfaces, you're not actually picking up any effective cutting flutes as I've yet to see a ball mill with more then 2 center cutting flutes.

    Sent...
  2. I purchased a new MM2 a year ago. For the first...

    I purchased a new MM2 a year ago. For the first 8 months, no probing routines l, sans a few, allowed z touch off. Now since having software updated due to other various problems, I have updated...
  3. Replies
    12
    Views
    632

    Rarely have I had a program be unable to be...

    Rarely have I had a program be unable to be calmed down significantly with smoothing/tolerance settings in Fusion 360.

    It doesn't make sense why it would go about doing things the hard way by...
  4. Replies
    2
    Views
    429

    I'd look into a solid carbide endmill, as big as...

    I'd look into a solid carbide endmill, as big as you can afford, with a corner rad on it. Thrown in a long side lock or shrink holder. And I would just use a 3d finish strategy and slowly ramp up...
  5. Pretty sure this will need to be programmed long...

    Pretty sure this will need to be programmed long hand. In for other solutions, though.

    Sent from my SM-G955U using Tapatalk
  6. Replies
    12
    Views
    717

    The only time I probe for diameter is when I'm...

    The only time I probe for diameter is when I'm wanting to get close on some oddball tool, threadmill, keyseat, etc etc. Otherwise it's just a waste of time, imo. I would rather program off wear comp...
  7. Check maritool Sent from my SM-G955U using...

    Check maritool

    Sent from my SM-G955U using Tapatalk
  8. Thread: 75 mm Air Vise

    by sirAIG
    Replies
    3
    Views
    261

    Haas ought to be able to supple solid files if...

    Haas ought to be able to supple solid files if you ask.

    Sent from my SM-G955U using Tapatalk
  9. Replies
    9
    Views
    863

    Yeah, they suck for stringy chips. Only solution...

    Yeah, they suck for stringy chips. Only solution I ever had was to remove those manually before cycling the conveyor. I never left it running all the time as my cup accumulation was minimal most...
  10. Replies
    10
    Views
    463

    1991 Bridgeport Discovery 308 Lag

    EMI (electro mechanical integrators) in Pennsylvania services all the older birdgeport stuff now, they may be of some help.

    Centroid may be of help on retrofit.
  11. Makes perfect sense. Thanks for the explanation...

    Makes perfect sense. Thanks for the explanation and sample code! I understand what needs to happen now. I still plan to get half indexing for turning, I want to be able to easily call as many tools...
  12. I've not run a y axis lathe, how do you call...

    I've not run a y axis lathe, how do you call different y and z offsets for same tool number?

    Sent from my SM-G955U using Tapatalk
  13. Is it being expected that throwing an endmill in...

    Is it being expected that throwing an endmill in a holder and seeing 2-3 thou of runout is not normal? They make little hammers for a reason. Just tap the runout in

    Sent from my SM-G955U using...
  14. Live holder questions with bmt65, 24 index turret

    If I order my st20y with 24 (half index?) station turret, am I able to use the dual output live tool holders to have potentially 2-4 (2 main, 2 sub) holders per live tool drive?

    Link to some...
  15. Replies
    3
    Views
    422

    bump, i know people have these turrets. what...

    bump, i know people have these turrets. what tooling do you all prefer?
  16. Replies
    6
    Views
    724

    Any other companies I should be looking into?

    Any other companies I should be looking into?
  17. Replies
    2
    Views
    360

    Supposedly the machines are ready to go, yet haas...

    Supposedly the machines are ready to go, yet haas still does have a dedicated run in program in the 0900 folder.

    Sent from my SM-G955U using Tapatalk
  18. Replies
    3
    Views
    422

    BMT65 Live and Static Holder Options

    I'm looking for suggestions on manufacturers/tooling options for a st20y BMT65 turret. Lyndex Nikkon has been recommended. I know little to nothing of live tool holders. Looking for the best...
  19. Thread: Haas Tooling?

    by sirAIG
    Replies
    8
    Views
    1,005

    I was put off by their goofy LOC's. IE 7/16" LOC...

    I was put off by their goofy LOC's. IE 7/16" LOC on an 1/8" endmill. For some, no big deal. I regularly am using all my flute length, even sometimes rubbing shank on parts that don't matter.
  20. Replies
    6
    Views
    724

    BMT65 Live and Static Holder Options

    I'm looking for suggestions on manufacturers/tooling options for a new live tool lathe w/ BMT65 turret. Lyndex Nikkon has been recommended. I know little to nothing of live tool holders. Looking...
  21. I appreciate everyone's insight. As to what...

    I appreciate everyone's insight. As to what parts we will be making, that's a hard one to answer as it changes daily. We do all of our business prototyping. I will more then likely start with some...
  22. As long as your wire gauge and breaker are...

    As long as your wire gauge and breaker are appropriate, call hfo for install. The tech will verify everything it set correctly as far as I know.

    Sent from my SM-G955U using Tapatalk
  23. Replies
    23
    Views
    2,253

    I imagine all those who cant get fusion to work...

    I imagine all those who cant get fusion to work well are those who can't adapt to technology/change. If you cant figure out how to use templates and tool libraries to program complex parts fast and...
  24. Sandvik vs. Walter vs. Iscar - New lathe, new tooling

    As the title suggests, I am looking to purchase a new cnc lathe. BMT65, 1" sticks. I come from a manual world, so this level of tooling is completely new.

    I need to establish a relationship with...
  25. Sandvik vs. Walter vs. Iscar - New lathe, new tooling

    I posted this to the wrong subforum, please delete.
Results 1 to 25 of 194
Page 1 of 8 1 2 3 4