Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: ballen

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. Replies
    28
    Views
    1,261

    The Y bellows do not limit travel. They...

    The Y bellows do not limit travel. They compress/collapse into the metal cover in back.

    The Z bellows do limit travel. But when you have set it up correctly, you can remove them in less than 2...
  2. My advice: call Uncle Franz. (1) Send a short...

    My advice: call Uncle Franz.

    (1) Send a short email explaining the problem with a couple of photos to [email protected] . Tell them your machine serial number and type.

    (2)...
  3. Replies
    972
    Views
    86,730

    Hi Dennis, I hope that after all of the...

    Hi Dennis,

    I hope that after all of the challenges and problems, you have got your FP2 into operation. Have you been able to use it?

    If you need to make shim washers or trim them to size, it...
  4. Replies
    3
    Views
    137

    I was once shown a nice system used on Thiel 140...

    I was once shown a nice system used on Thiel 140 or 150 manual mills.

    A long small-diameter plastic tube is placed into a slot on one side of the way dovetail (or perhaps behind the gib strip). To...
  5. To those of you who are grinding your own...

    To those of you who are grinding your own cutters, I would be grateful if you could please post a few closeups of the cutting edges. I have ground a handful of bits but I normally use insert...
  6. What tooling should I use in this boring bar?

    In my collection of stuff is this (probably home-made) boring bar. It's about 50mm (2") in diameter and about 200mm long, and I'd like to use it for making some clean 60mm holes in cast iron. It has...
  7. Replies
    28
    Views
    1,261

    If you are missing leadscrew handwheels I may...

    If you are missing leadscrew handwheels I may have the right style/size.

    A handful of comments based on the photos:

    - At first I thought that the machine was rusty, but it seems to
    be dried...
  8. The Deckel manual calls for "general purpose...

    The Deckel manual calls for "general purpose roller bearing grease" at the two lubrication points of the dividing head. Since this is low-speed operation, provided that you are not flooding the...
  9. Replies
    3
    Views
    328

    Hi John, I'm glad this was helpful. If...

    Hi John,



    I'm glad this was helpful. If your questions were *not* answered in those links, please ask here, perhaps attaching a photo or two for guidance. There is tremendous expertise...
  10. Replies
    972
    Views
    86,730

    A few years ago I needed some thin washers for...

    A few years ago I needed some thin washers for adjusting the position of a bevel gear in the support (the one at the top of the feed shaft, in between the bevel gears that drive the X-axis clutches)....
  11. This is a tricky issue. In the 1955 FP2 manual...

    This is a tricky issue. In the 1955 FP2 manual they want gearbox oil in that reservoir. In the 1964 manual they call for way oil. I think this is because the design changed. There is a post of...
  12. Replies
    28
    Views
    1,261

    The threaded shaft and flange are indeed the...

    The threaded shaft and flange are indeed the Y-axis lead screw. The gray half circle next to it is the back cover and attachment point for the Y-axis bellows. I have NOT seen the right angle...
  13. Well done! Please could you spend a minute and...

    Well done! Please could you spend a minute and post a table showing which pins of the DB15 were connected to which of the RSF colors? That will help the next person with this question.
  14. Replies
    28
    Views
    1,261

    Does it have the horizontal head? I don’t see it...

    Does it have the horizontal head? I don’t see it in the photos.


    Sent from my iPhone using Tapatalk
  15. Replies
    28
    Views
    1,261

    Welcome, and congratulations on the nice machine!...

    Welcome, and congratulations on the nice machine! My Deckel is FP2 #4224 and is from 1964, so I think your machine must be from 63 or 64 and very similar.

    Please edit your post to embed the...
  16. The one on the left looks like a surface grinder,...

    The one on the left looks like a surface grinder, is the one on the right a centerless grinder?
  17. Replies
    972
    Views
    86,730

    Dennis, I realise that I am not sure how the gear...

    Dennis, I realise that I am not sure how the gear mesh is set. Perhaps the 3 setscrews are only to set the preload on the thrust bearing, and the gear mesh is set with thin spacer or shim washers. I...
  18. John, I think I have a spare set of 7EL brushes,...

    John, I think I have a spare set of 7EL brushes, which you can have (I ended up buying a BL40). Ping me on the weekend and I'll rummage around for them. Cheers, Bruce
  19. Replies
    3
    Views
    328

    I assume you mean the bevel gears that drive the...

    I assume you mean the bevel gears that drive the X-axis lead screw clutches. The only way to remove these is by pulling down the top one of the two bronze bushings that sit under the central gear....
  20. Hi Richard, Since the bronze 6" costs more...

    Hi Richard,



    Since the bronze 6" costs more than the cast iron 6", there must be some advantage. What is that?

    Cheers,
    Bruce
  21. Yes, they are the same. See the last page of the...

    Yes, they are the same. See the last page of the spec linked in post #5. It reads as below. This is effectively the same as the Heidenhain 11 microamp spec.

    Microcurrent Sine Wave
    7-16mA (11.5...
  22. Replies
    36
    Views
    23,997

    The post you are responding to is 10 years old!

    The post you are responding to is 10 years old!
  23. Replies
    972
    Views
    86,730

    But I thought you wrote "Yeah, that", meaning...

    But I thought you wrote "Yeah, that", meaning that that the noise level changed when you switch the long reach head on/off with the rotary 0/1 control. If so, then the problem is likely the bevel...
  24. Replies
    972
    Views
    86,730

    My machine is a close sibling of yours. When I...

    My machine is a close sibling of yours. When I engage/disengage the 0/1 knob it does affect the noise level, but not that much. Perhaps you should check if you have set the engagement of the large...
  25. I'm gradually turning this into metal. First...

    I'm gradually turning this into metal. First step was to attach a clamping bracket to the front of the grinding head. I decided to do that with hand tools and a jig rather than removing the...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4