Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: rons

Page 1 of 60 1 2 3 4

Search: Search took 0.03 seconds.

  1. Replies
    23
    Views
    927

    My internet slows down by design. If I have...

    My internet slows down by design. If I have several hours of non-use or swap the cable to another computer the speed goes down.
    A reset on my internet box brings the speed right back up. I called...
  2. Just got back from Target. Bought a few jars of...

    Just got back from Target. Bought a few jars of peanut butter, some Milk Bone boxes, and a dvd.
    The kid's section had an assortment of weapons, namely something that looked like a scaled down XM-18....
  3. 1. A textbook answer is that a measurable...

    1. A textbook answer is that a measurable quantity of grease should fill the bearing. Using just a grease port is not accurate. And it does not allow all the older grease to be expelled.

    2....
  4. Replies
    19
    Views
    780

    A Forstner style bit. Probably will need a shank...

    A Forstner style bit. Probably will need a shank extension.
  5. Replies
    12
    Views
    556

    Find a scraped out motor frame with the mount you...

    Find a scraped out motor frame with the mount you want. Dissect the motor and cut off the mount. Probably a angle grinder would do it.
  6. Replies
    24
    Views
    1,045

    I do not use any of those old style overload...

    I do not use any of those old style overload heaters. This one is adjustable from 2.5 to 10 amps. I have another that is 9 to 18 amps.

    263250

    This one is like the one I have and it has two...
  7. Replies
    50
    Views
    3,425

    You can get a pedicure at the same time.

    You can get a pedicure at the same time.
  8. Replies
    9
    Views
    1,201

    Lay a slab flat on a table. Then place your...

    Lay a slab flat on a table. Then place your coffee mug on top. Will keep it warm.
  9. Replies
    24
    Views
    1,045

    You can look around for point contact kits. They...

    You can look around for point contact kits. They are available but look at yours first. Don't file the metal down but just use a brass bristle brush to clean them up.
    And if they are pitted be sure...
  10. Replies
    24
    Views
    1,045

    The H30's mean the starter was previously running...

    The H30's mean the starter was previously running on 460.
    Now you propose to use H37's on 230. You already know that the rating is 3Hp for 230. If this was continuous closure then the match is not...
  11. Replies
    24
    Views
    1,045

    Sorry. You might not be good there having three...

    Sorry. You might not be good there having three wires there. I don't go past two using spade connectors.
  12. Replies
    24
    Views
    1,045

    Dayton Model 5X155B NEMA Size 1 Magnetic Motor...

    Dayton Model 5X155B NEMA Size 1 Magnetic Motor Starter. For 3 HP 120V, 7-1/2 HP 208 to 230 V and 10 HP 430/460 VAC.

    Line taken from a spec. Notice the ratings and how they change. What voltage are...
  13. Replies
    15
    Views
    551

    Then you have a year to do research and build the...

    Then you have a year to do research and build the RPC yourself. And your idler motor dream is way too much. 10 Hp is where you are at, maybe a little less.
  14. Replies
    24
    Views
    1,045

    I suggest that you make your presentation more...

    I suggest that you make your presentation more clear rather than have it come as bits and pieces. A drawing like that invites guesses and more questions.

    Sounds like I'm too critical. No. I would...
  15. Left out the incident this year at the Gilroy...

    Left out the incident this year at the Gilroy Garlic Festival in CA.

    Look at the number of people who drown in swimming pools each year. The numbers above are all clumped into one bunch from past...
  16. Another example of a communication channel...

    Another example of a communication channel interrupted by white noise. Must have their squelch control adjusted just right.

    Looks like they totally ignored you.

    LOL
  17. Replies
    8
    Views
    425

    The derate factor is something I didn't want to...

    The derate factor is something I didn't want to mention until I looked at the documentation.

    What is the model name/number of the drive? You never know, someone might have the same model.
  18. Replies
    8
    Views
    425

    Find ABB model number if (unable to find...

    Find ABB model number

    if (unable to find manual on internet)
    then ask question

    if (unable to find answer in manual)
    then ask question
  19. Replies
    17
    Views
    944

    The carbon steel taps and dies are good for...

    The carbon steel taps and dies are good for reforming threads. Mostly in soft materials and thin metal.

    The thickness of material will dictate how easy the tap can be removed after it breaks. Say...
  20. Replies
    32
    Views
    1,449

    This happened with my Miller cooler fittings. The...

    This happened with my Miller cooler fittings. The original fittings are plated and the top side has a press fit pipe.
    If you change coolant every 6-12 months then you wouldn't notice anything until...
  21. Replies
    32
    Views
    1,449

    That is an option that has to be purchased. Ask...

    That is an option that has to be purchased. Ask at the millerwelds forum.
  22. Those are fine products. I bought some of this...

    Those are fine products.

    I bought some of this stuff in a bundle of 41'. Lengths of 21', 11', and 9'. Only cost $35 so I'm just going to use what I already have.
    ...
  23. Replies
    13
    Views
    890

    Does a peristaltic pump deliver the flow rate?...

    Does a peristaltic pump deliver the flow rate? Don't think so. Those pumps are used in closed systems for medical use.

    Take apart the little pump, the bearings probably have had it.
  24. I know 3 out of 4 of these guys believed in gun...

    I know 3 out of 4 of these guys believed in gun control. And then murdered their people.

    The eight despots we love to hate - in pictures - Telegraph
  25. Replies
    3
    Views
    361

    If you want brand new. Heard no bad comments...

    If you want brand new. Heard no bad comments about the mills. If the lathes have the same reputation:

    Sharp Machine Tools | Lathes >> Index
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4