Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: Superbowl

Page 1 of 2 1 2

Search: Search took 0.00 seconds.

  1. As others have pointed out, there are better ways...

    As others have pointed out, there are better ways to do this like with a plasma cutter. However if you want to use the BP then make a mandrel to mount the discs in the spindle and put a single point...
  2. Replies
    25
    Views
    1,275

    The largest end mill holder I have for BP can...

    The largest end mill holder I have for BP can take a 1.5 inch mill shank so I could not even mount this sucker but I do have some two inch end mills with a 1.5 inch shank. While I would never...
  3. Replies
    27
    Views
    1,691

    Just get out a file and make it pretty.

    Just get out a file and make it pretty.
  4. Replies
    17
    Views
    912

    I got an email from Fluid Systems today that the...

    I got an email from Fluid Systems today that the B3905 5psi unit I ordered is on back order for at least a month. Therefore I am now going to try the 10psi B3906 that costs $10 more.
  5. Replies
    17
    Views
    912

    Thanks for all the help guys. I just ordered a...

    Thanks for all the help guys. I just ordered a B3905 from Fluid Systems for $22.49 including shipping. B3905 is a 5psi check valve with the correct 1/8 npt threads so no 90 degree thread change...
  6. Replies
    5
    Views
    669

    I really like six jaw chucks and have one on my...

    I really like six jaw chucks and have one on my Clausing with an L00 mount. I hope to pick up one for the 10EE D1-3 at some point in the future.
  7. Replies
    17
    Views
    912

    That may be correct Cal, and why it is so much...

    That may be correct Cal, and why it is so much more expensive than other fittings. I will call some of the third party sellers others have recommended but no one shows this fitting on their web site....
  8. Replies
    17
    Views
    912

    10EE apron Bijur unit

    I took the apron off my 1957 10EE and have found the Bijur metering unit that feeds the well with the cloth packing and pipe cleaner wicking was clogged. It is marked as a MRA-00. I could not find...
  9. Replies
    9
    Views
    1,028

    As to the sawing? Keep clearing the gullets....

    As to the sawing? Keep clearing the gullets. "Keep the spindle turning AND use full-blade saw strokes or near-as-dammit with the hand hacksaw."

    I forget who it was, perhaps Keith Rucker or one of...
  10. I have done holes about that size in1/4" steel...

    I have done holes about that size in1/4" steel plate with a HHS hole saw. Just go slow and use a lot of oil. Drill a little and let the hole saw cool. Once you over heat it, it is trash. I also have...
  11. Replies
    13
    Views
    1,316

    10EE in Michigan for less than Two Grand

    If only I had more room

    MONARCH 10EE, CLEANING HOUSE, RUNNING, ALL RELATED TOOLING, 1944 | eBay
  12. It looks like your main problem is interference...

    It looks like your main problem is interference with the hand wheel below. I can not tell from the photo how much lower that is.
  13. Replies
    34
    Views
    1,960

    Since your stock is only 1/2" it can pass through...

    Since your stock is only 1/2" it can pass through the head stock of any lathe. I would set up a pipe type support on a tripod to the rear of the head stock to keep the pickets from whipping around....
  14. Replies
    12
    Views
    1,159

    Thanks for the info. I think my slot will allow...

    Thanks for the info. I think my slot will allow me to mount the scale with no drilling of new holes. I will drill to mount the safety bumpers like you did however.
  15. Replies
    11
    Views
    1,475

    From what I found on line that is a 10,000 lb....

    From what I found on line that is a 10,000 lb. machine so it will take somebody that wants it bad to haul it off. I would first try Craigslist and Ebay. Someone who sees it there might take it for...
  16. Replies
    22
    Views
    1,537

    You of course are going to have to drill it out....

    You of course are going to have to drill it out. There is no other way. To drill out a broken bolt, I always use a left hand drill bit and run the drill in reverse. Usually at some point in the drill...
  17. Replies
    12
    Views
    1,159

    Thanks Rimcanyon. Did you use tee bolts in that...

    Thanks Rimcanyon. Did you use tee bolts in that slot to mount your scale or drill separate holes?
  18. Replies
    28
    Views
    11,799

    For less than $3,000 you can buy a used...

    For less than $3,000 you can buy a used Bridgeport mill to use as a drill press which will more useful and robust than any DP.
  19. Replies
    12
    Views
    1,159

    Does anyone know what the sliding threaded piece...

    Does anyone know what the sliding threaded piece that rides in the channel on the side of cross slide is for? I will have to remove it to mount the scale.
  20. Replies
    12
    Views
    1,159

    Thanks for the photos Peter. Using an indicator...

    Thanks for the photos Peter. Using an indicator to make sure every thing is aligned is a great idea. I have not even gotten to the point of thinking about alignment yet.
  21. Replies
    12
    Views
    1,159

    Mounting a scale to 10EE cross slide

    Hi Guys. I have a new to me 1957 10EE that came with a Sony DRO. The previous owner mounted the carriage scale but not the cross slide scale. I am not sure the best way to mount a scale to the cross...
  22. Check your lease in case it is non-standard....

    Check your lease in case it is non-standard. However if the lease is silent on the issue then as a 40 year real estate broker I can tell you that such improvements (called a trade fixture) in a...
  23. Likely the best and easiest would be to buy two...

    Likely the best and easiest would be to buy two CB radios. Thay are still available new and used are for sale on Ebay with working units starting at $5.

    If you only need signalling then a...
  24. Replies
    21
    Views
    1,514

    Essential Business is anything that involves the...

    Essential Business is anything that involves the use of toilet paper, which as we all know is in short supply.
  25. just replaced the front tires on my Kubota and...

    just replaced the front tires on my Kubota and had very good luck using my 3 ton arbor press to break the beads. Went fast and easy.
    I
Results 1 to 25 of 37
Page 1 of 2 1 2