Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: wippin' boy

Page 1 of 60 1 2 3 4

Search: Search took 0.05 seconds.

  1. pull the part find a new supplier

    pull the part
    find a new supplier
  2. Replies
    7
    Views
    630

    sounds like a bad sensor to me

    sounds like a bad sensor to me
  3. Replies
    1
    Views
    345

    the bearing pack on the headstock end of those...

    the bearing pack on the headstock end of those things used to rust up and bind up.
    you can take the whole setup out towards the servo without removing the screw
  4. Replies
    19
    Views
    1,445

    seems to me by pulling the pivot pin you actually...

    seems to me by pulling the pivot pin you actually made it like my old hardinge cobras.
    with the head stock free to move "straight " front to back you manipulated the height relationship because of...
  5. Replies
    19
    Views
    1,445

    the 8's and 15's were linear guides the 10's and...

    the 8's and 15's were linear guides
    the 10's and 20's were still box ways
  6. Replies
    19
    Views
    1,445

    I hate to be a bad news guy here but it is...

    I hate to be a bad news guy here but it is possible with this old machine that wear on the bed has actually dropped -x-
    if that's the case drill pockets centerline would be my preference over...
  7. Replies
    19
    Views
    1,445

    1) level machine insuring no bed twist. you know...

    1) level machine insuring no bed twist. you know when this is so when you can put a spirit level on turret and move from one end of z to the other with no change in bubble
    2) headstock taper 6"...
  8. Replies
    19
    Views
    1,445

    from what you have said about what all is loose I...

    from what you have said about what all is loose I think this is your issue

    "some off those old long beds the swivel point on the head stock is so far back from the chuck you have to make a 20...
  9. Replies
    19
    Views
    1,445

    your no tgetting all the bolts loose enough if...

    your no tgetting all the bolts loose enough
    if it's been awhile the two castings might be stuck/rusted together and are gonna need a wack or two
    if I recall correctly the pin you are talking about...
  10. turn one of these around backwards mcmastet...

    turn one of these around backwards
    mcmastet carr or anybody

    275315
  11. pretty sure I've told you how to do most of 'em...

    pretty sure I've told you how to do most of 'em
    if you dont remember we're screwed :codger:
  12. turret radial relocation headstock taper x...

    turret radial relocation
    headstock taper
    x center line number reset
    diagnostic fundamentals
    using electricals for troubleshooting
    parameter edit
    reinitialize :eek:
    chuck barriers
    tailstock...
  13. Replies
    3
    Views
    726

    it was a similar "won't come all the way up"...

    it was a similar "won't come all the way up" thing
    I do t remember the exact hang point.
    I'll go ahead and credit your bill :rolleyes5:
  14. Replies
    15
    Views
    1,644

    I use these hole saws from McMaster carr ...

    I use these hole saws from McMaster carr

    272931

    and cut squares with a 3" cutoff

    272933
  15. Replies
    3
    Views
    726

    I had a dt20 that vintage that had some burn...

    I had a dt20 that vintage that had some burn damage on the main i.o. board
    came from some cable rub in the in/out slide on the monitor
  16. or not:angry: good luck

    or not:angry:
    good luck
  17. 271431 if you can look at this and figure out...

    271431

    if you can look at this and figure out what you have from the diagram on the valve you can probly get it out of McMaster carr forin one day

    271432
  18. all world in chicago Illinois has alot of parts...

    all world in chicago Illinois has alot of parts and can cross the parker numbers

    815-943-9111

    that's a common directional valve with standard mount
    from that number all world can probly match...
  19. I have never heard of such a parameter if you...

    I have never heard of such a parameter
    if you where desperate to stop the chuck movement you could pull the coil connector before turning on
  20. search mylar at McMaster carr I've used it...

    search
    mylar
    at McMaster carr
    I've used it with success for overlay repairs
  21. Replies
    1
    Views
    499

    I dont think this is the right page for what you...

    I dont think this is the right page for what you are after
    chuck open and close are going to be much lower than "xc"
    from there it's been to long since I been in a t32 but it seems you toggle to an...
  22. Replies
    2
    Views
    576

    if you can get a generic set of parameters you...

    if you can get a generic set of parameters you should be able to get it going
    you might have trouble with a couple options like tool eye or programmable tailstock but you can get by without that...
  23. Replies
    1
    Views
    445

    GTI spindle technology might have a shop in...

    GTI spindle technology might have a shop in Michigan. I know they have ones in illinois
  24. Replies
    7
    Views
    1,139

    I've used them run of the mill Bridgeport clone...

    I've used them
    run of the mill Bridgeport clone
    parts available out of California
    I'd buy one if price and condition is what I needed
  25. Replies
    2
    Views
    547

    with a two foot bar you can get "some" movement...

    with a two foot bar you can get "some" movement
    cats right
    you need to go in there and look around
    could be nothing more than dirt floating around in there on that curveck could be a pinch couple...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4