Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: david n

Page 1 of 60 1 2 3 4

Search: Search took 0.04 seconds.

  1. Thread: B&A Precision

    by david n
    Replies
    5,672
    Views
    954,578

    I'd rather go into hotdog...

    I'd rather go into hotdog sales......................if'n you're not already in the AR game, the money is pretty skimpy.
  2. Thread: B&A Precision

    by david n
    Replies
    5,672
    Views
    954,578

    Man, to ride again....................I have a...

    Man, to ride again....................I have a good friend that is an enduro/hair scramble guy...............bugs me all the time to get a bike and just do some off-road/logging trail/dirt road...
  3. I'll 'splain...................The one in the...

    I'll 'splain...................The one in the pick makes a flat bottom groove with a 45° back chamfer............that's what I'm goin for.............other similar bars have a few degree angle on the...
  4. These will do................thanks. They are...

    These will do................thanks.

    They are for a higher(ish) volume 1 OP part in 6061 that has little margin...............I bore and back chamfer with this tool with no need to deburr the...
  5. Replies
    12
    Views
    726

    She was over heatin'......................there's...

    She was over heatin'......................there's a high pressure valve for the refrigerant?.............if'n it gets too hot, valve pops and it stops cooling. The cooling fins where pretty gunky...
  6. Where to find? Solid carbide thread relief/ back chamfer boring bar..................

    So I can't find these little bars any where any more.(see pic)...................This one is a circle machine(who is now Widia?) and I believe they no longer make them.....................I found a...
  7. Replies
    12
    Views
    726

    Air dryer restricting air flow?

    Kaiser refrigerant air dryer seems to be blocking air flow.................randomly getting machines alarming out due to low air pressure. Gauge on the tank reads 120PSI............compressor is...
  8. I was feelin a little rusty too...........but...

    I was feelin a little rusty too...........but then I smoked a handful of these varmints at 170 +/- yards with the HMR........................

    325335
  9. Replies
    2
    Views
    597

    RFQ: Small threaded rod. 1000pcs

    Simple part. 1000pcs.

    +/-.005" Small thread relief allowed. 2A thread.

    Low carbon steel. I normally use 12L14. 3/16"Ø stock material is OK. If you go with 1018, threads must but smooth. Not...
  10. Replies
    42
    Views
    3,051

    Did I miss something? Was this supposed to be in...

    Did I miss something? Was this supposed to be in this thread?
  11. Replies
    26
    Views
    2,162

    If you can do the Brother, that will be much more...

    If you can do the Brother, that will be much more versatile than the CM or the Datron...............you can still make tiny parts and you can make larger parts. And as stated above, multiple vises...
  12. Replies
    42
    Views
    3,051

    With worldwide sourced parts(and Yanmar...

    With worldwide sourced parts(and Yanmar diesels)..................Mahindra and Yanmar "build" their tractors in the US too.....Kubota too........................I'm sure the Deeres are 'more" made in...
  13. Replies
    42
    Views
    3,051

    I have a "Cub Cadet"....................No...

    I have a "Cub Cadet"....................No Binder.............100% Yanmar. I've had it for close to 9 years now and it has had zero issues. Very clean simple build. All of the castings are very nice....
  14. Replies
    139
    Views
    20,220

    Now you can retire……….

    Now you can retire……….
  15. Huh? Too expensive? One cheap CNMG insert could...

    Huh? Too expensive? One cheap CNMG insert could literally run a few tons of brass........................................

    What tooling do you normally use in your lathe? Just run...
  16. Replies
    26
    Views
    2,162

    A Speedio is leaps and bounds beyond a...

    A Speedio is leaps and bounds beyond a Haas....................I would not put them in the same class of small machine.

    The Neo is a whole 'nother animal and I will admit, I don't know much about...
  17. Replies
    26
    Views
    2,162

    What are little parts in your world? Do they fit...

    What are little parts in your world? Do they fit in a thimble or are they the size of a deck of cards?

    There is this state of mind I see over and over here on PM and else where when someone wants...
  18. Replies
    163
    Views
    10,136

    4-5 days? Heck that’s generous……..I’m getting...

    4-5 days? Heck that’s generous……..I’m getting quotes that are only good for 48 hrs.
  19. Thread: 8020 Principle

    by david n
    Replies
    129
    Views
    8,697

    I knew you were tryin to flush that outa...

    I knew you were tryin to flush that outa him................a while ago in a different thread he went on and on and on about how the rest of us shop owners are morons for having more than one...
  20. Replies
    163
    Views
    10,136

    Big stainless job is comin up that was ordered a...

    Big stainless job is comin up that was ordered a few months ago..............told my customer to cough up some gelt and buy right away. I'm sure he's glad he did back in March........prolly 10k lbs...
  21. Replies
    163
    Views
    10,136

    Ox, Quit quoting the guy................all he...

    Ox,
    Quit quoting the guy................all he does is insult an berate others................of the Big B posts I have read(very few)......he's nothing but a troll. Hardly ever actually contributes...
  22. Straight line rip saw is out...............spendy...

    Straight line rip saw is out...............spendy and I don't a room for more toys......................it would be the way to go though...........



    Nope.............how do you rip a straight...
  23. Replies
    609
    Views
    112,609

    So the horizontal holes in this pic are...

    So the horizontal holes in this pic are completely new and intersecting with the grooves getting machined in the last pic with the part on the rotary?
  24. No comment...............................:leaving:

    No comment...............................:leaving:
  25. Thread: 8020 Principle

    by david n
    Replies
    129
    Views
    8,697

    I have a few items I make for customers that are...

    I have a few items I make for customers that are barely break even, some cost me..................they don't know that, but it keeps the other very profitable 20-30 part numbers in my...
Results 1 to 25 of 1500
Page 1 of 60 1 2 3 4