Search Results - Practical Machinist - Largest Manufacturing Technology Forum on the Web
Close
Login to Your Account

Search:

Type: Posts; User: setlab

Page 1 of 5 1 2 3 4

Search: Search took 0.01 seconds.

  1. Replies
    24
    Views
    1,697

    I didn't know Google translate could read...

    I didn't know Google translate could read pictures ��
  2. Replies
    24
    Views
    1,697

    Is this Japanese writing or Chinese writing?

    I picked up an indexer for a pretty good deal last week. Is this a Chinese one or a Japan one?


    266438266439
  3. Replies
    8
    Views
    1,261

    Hey who knows, but I've never won the lottery yet...

    Hey who knows, but I've never won the lottery yet lol. I figure if I'm the only bidder which I probably will be I can pull that t slot table off and use it as a fixture plate for something down the...
  4. Replies
    8
    Views
    1,261

    What is this? Hudson vertical mill

    So I found an online auction and was browsing threw it and found this "Hudson vertical mill" listed with only one shitty picture... gotta love the effort of auctioneers. Anyways its past the viewing...
  5. Replies
    19
    Views
    1,814

    I need to look again, but I have 2 maybe 3/4"...

    I need to look again, but I have 2 maybe 3/4" arbors and a larger one, maybe a 1" or 1.5" and then I have I think 4 end mill holders going up to 3/4", a devider head, and a handful of Mt3 shank mills...
  6. Replies
    19
    Views
    1,814

    I was lucky to get a few arbors and some end mill...

    I was lucky to get a few arbors and some end mill holders with it. Even a really old indexer so I'm mostly set there. I don't have many cutters for the arbor yet though but that's something I can do...
  7. Replies
    19
    Views
    1,814

    Did not know that, this is my first horizontal...

    Did not know that, this is my first horizontal mill but I do have a bunch of t slot clamps. When I bought it there was an angle plate on the table, do a lot of guys just indicate a plate like that...
  8. Replies
    19
    Views
    1,814

    WTB small milling vice

    I picked up a small horizontal mill with a 6"x20" table and need a small vice for it. Located near Dayton Ohio.
  9. Thanks I'll check for the manual. I bought a...

    Thanks I'll check for the manual.

    I bought a little horizontal mill built back in the 50s from the same guy and the machine surfaces look near unused on it. May be because it is more of a...
  10. I'll check your tread out tomorrow, looks like I...

    I'll check your tread out tomorrow, looks like I have to register to check out the pictures.

    What makes these grinders fussy? I imagine the number of mechanical parts is more chance to bind up...
  11. I still have to go and look at it a second time,...

    I still have to go and look at it a second time, the only markings I saw on it were brown and sharp no2 molded on to the base casting.

    So is there anything holding the table onto the machine or...
  12. Brown and sharp no2 surface grinder question

    I have an opportunity to buy a brown and sharp no2 surface grinder for $300. From what I've see of it so far the grinder is buried in a small hole with probably 30 years of barn dust/oil on it.
    ...
  13. So no harm in not having a knife switch /breaker...

    So no harm in not having a knife switch /breaker box in between the converter and machines?

    I'll pass along the subpanel advice, that seems like a good idea.

    This converter never runs more than...
  14. Do rotary phase converters need a breaker box?

    Not my phase converter but I was recently asked a question maybe you guys could help with. This old 3 phase converter has been in use without any issues for years. At the time it was pieced together...
  15. Replies
    6
    Views
    866

    I could do what I need to with a Drill, I just...

    I could do what I need to with a Drill, I just would rather not deal with a 1" twist drill again in the mill or drill press. More of a convenience/new thing for me too, I've never used annular...
  16. Replies
    6
    Views
    866

    That's not bad, I take it those are Chinese ones?

    That's not bad, I take it those are Chinese ones?
  17. Replies
    6
    Views
    866

    WTB Annular cutters

    I need a 5/8" and a 1" cutter, preferably with center pins for an upcoming project if anyone has some in the bottom of a drawer somewhere.
  18. Replies
    7
    Views
    776

    They had a pneumatic drawbar installed on it. I'm...

    They had a pneumatic drawbar installed on it. I'm fingers crossed that some leverage will work. Cause I'm probably not getting out the wrenches to take it apart.

    It's going to drive me crazy...
  19. Replies
    7
    Views
    776

    I was going back Monday anyhow, I should have...

    I was going back Monday anyhow, I should have taken some pictures though. I'll try the screwdriver method.
  20. Replies
    7
    Views
    776

    How to remove tooling without power?

    Not the normal topic here I know... But I was checking out the local scrap yard today and came across a cnc mill that had been scrapped out. It had a handfull of different tool holders and collet...
  21. Replies
    18
    Views
    1,080

    242760 It's definitely a square insert, excuse...

    242760

    It's definitely a square insert, excuse my mini square I promise I don't use it for anything precise lol. I'm not a huge fan of that tool holder but it was practically free at an auction a...
  22. Replies
    18
    Views
    1,080

    Is this the right insert for my lathe tool?

    This is the first time I'm bothering with buying inserts for my lathe tools,but from what I can tell the insert I need is a ssn-43 is that right? What do all those other numbers mean?

    Also, is...
  23. Replies
    4
    Views
    877

    Are these air fittings good for anything?

    So I was going threw a box of stuff in my barn and came across these. They appear to be quick connects for air but I've never seen this style before. My shop and tools have a different style of...
  24. Replies
    2
    Views
    1,354

    Big ass hossfeld bender, what do I got?

    Anyone know anything about hossfeld special long frame benders? I have one on my barn attic that I'm on the ropes about keeping or not. So far Google hasn't told me anything, the largest bender I've...
  25. Replies
    7
    Views
    1,190

    I take it all taper pins are the same taper? This...

    I take it all taper pins are the same taper? This lathe is my first run in with taper pins.
Results 1 to 25 of 125
Page 1 of 5 1 2 3 4